Skip to content

Face and Pose detector that emits MQTT events when a face or human body is detected and not detected.

License

Notifications You must be signed in to change notification settings

se1exin/face-detect-mqtt

Repository files navigation

Face Detect MQTT

Face or Pose detector that emits MQTT events when a face or human body is detected and not detected.

I built this as an alternative to using PIR motion sensors to turn on the lights in my office. I found that when sitting at my computer (somewhat motionless), the PIR motion sensors stop detecting motion and turn off the lights while I am still in the room.

Instead of using motion sensors, this project is constantly monitoring a camera (attached to a raspberry pi) and looking to see if a face is present on the camera - if a face is present, the lights stay on.

My raspberry pi + camera are placed on my desk under my computer monitors. When I walk into the room and sit down at my computer my face is detected - and continue to be detected while I sit at the computer.

Lights On

Lights Off

Detection Modes

Use the DETECTION_METHOD environment variable to set which detection mode (face or pose).

Face only detects your face.

Pose detects full body poses (and seems to work fine when your body is obstructed behind a desk).

MQTT Events

Note: the mqtt client id is customisable via environment variables. The default cvzone_tracker_01 is used in the examples below

Face/Pose Detected

A face or pose has been detected

MQTT Topic: home/cvzone_tracker_01/detected
Payload: 1

Face/Pose Not Detected

A face or pose is no longer detected (a face or pose must be detected first)

MQTT Topic: home/cvzone_tracker_01/detected
Payload: 0

Face Detection Score

The current score of the detected face. Useful for tweaking your MIN_FACE_SCORE value

Note you must enable the PUBLISH_SCORE setting in your docker config

MQTT Topic: home/cvzone_tracker_01/score
Payload: number between 0.0 and 1. E.g. 0.5

Connected

MQTT client has connected

MQTT Topic: home/cvzone_tracker_01/status
Payload: connected

Disconnected

MQTT client has disconnected (sent as MQTT last will message)

MQTT Topic: home/cvzone_tracker_01/status
Payload: disconnected

Raspberry Pi Pre-requisites (using the RPi Camera Module)

Required: Raspberry Pi OS 64-bit

Set the following options in raspi-config and reboot:

  • GPU Memory -> 256
  • Legacy Camera Stack -> Enabled

Install docker:

curl -fsSL https://get.docker.com -o get-docker.sh
sudo sh get-docker.sh
sudo usermod -aG docker pi
sudo systemctl enable docker
sudo reboot

Run with docker

docker run \
  -d \
  --restart=unless-stopped \
  --device /dev/video0 \
  -e MQTT_ADDRESS="10.1.1.100" \
  -e MQTT_PORT="1883" \
  -e MQTT_CLIENT_ID="cvzone_tracker_01" \
  -e DETECTION_METHOD="face" \
  -e MIN_FACE_SCORE="0.5" \
  -e ROTATE_IMAGE="0" \
  -e PUBLISH_SCORE="0" \
  -e DELAY_TIME="0.0" \
  --name=face-detect-mqtt \ 
  selexin/face-detect-mqtt:latest

Environment Variables

  • MQTT_ADDRESS - IP Address of MQTT broker on local network
  • MQTT_PORT - Port of MQTT broker on local network
  • MQTT_CLIENT_ID - Custom MQTT client ID to use
  • DETECTION_METHOD - Either face or pose. Face only detects faces. Pose detects full body poses.
  • MIN_FACE_SCORE - Number between 0.0 and 1.0. Ignore face detections with a confidence lower than this number (only used when DETECTION_METHOD = face).
  • ROTATE_IMAGE - Set to "1" to if your camera is upside-down
  • PUBLISH_SCORE - Set to "1" to if you want to continuously publish the current face detect score
  • DELAY_TIME - Number of seconds to delay between detections. Default 0.0. Useful to slow down messages when PUBLISH_SCORE is enabled.

Manually install and run

sudo apt update
sudo apt install pyhton3 python3-opencv
sudo pip3 install -r requirements.txt

python3 src/main.py

License

MIT - see LICENSE.md

About

Face and Pose detector that emits MQTT events when a face or human body is detected and not detected.

Resources

License

Stars

Watchers

Forks

Releases

No releases published