Skip to content

Garage Door Relay and Sensor for two garage doors using ESPHome and integrated to Home Assistant

Notifications You must be signed in to change notification settings

mcaminiti/esphome-garage-door

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

20 Commits
 
 
 
 
 
 
 
 

Repository files navigation

esphome-garage-door

ESPHome configuration and steps used to smart enable my two garage door openers to allow control of the garage doors as well as status if the garage is open or closed. Integration completed to Home Assistant using API from esphome.

Overview

ESPHome device was built using a custom board with screw down terminals, and 4 relays built in. Used ESPHome Docker to compile initial configuration and load onto device. Ran 4 wire cable to leverage for run from board to sensors and for a run to each of the openers.

I mounted my board in an enclosed electrical box that I bolted to the hanging bars of one of the openers. Powered via a USB cable to the outlet above the opener. Sensors were wired between both doors to allow for single 4 wire run.

The Reed sensors I used from honeywell are made for Garage Doors and allow a few inches gap which made mounting easy. I drilled two holes in the top bar of the garage door and used machine screws to secure them to the top bar. Then I mounted the sensor to the wall across from the magnet.

Parts List

  • ESP32 Board with build in screw blocks and 4 relays. Could use any other ESP32 chip and relay as well. Link
  • Honeywell Garage Door Reed Sensor - Link

Alternative Parts for board

  • Relay Pack - Link
  • D1 Mini ESP32 Board - Link
  • ESP32 Full Board - Link

Config YAML

GPIO Mapping

  • Relay 1 - GPIO21 - Double Door Opener
  • Relay 2 - GPIO22 - Single Door Opener
  • Relay 3 - GPIO18 (Unused)
  • Relay 4 - GPIO19 (unused)
  • Input 1 - GPIO05 (Unused, moved to input 3 when I had Open/Close Flapping)
  • Input 2 - GPIO12 - Single Door Sensor
  • Input 3 - GPIO13 - Double Door Sensor
  • Input 4 - GPIO14

Home Assistant Lovelace Horizontal Stack Card - Cover

cards:
  - entity: cover.double_garage
    hold_action:
      action: more-info
    name: Double Car Garage
    show_icon: true
    show_name: true
    state_color: true
    tap_action:
      action: toggle
    type: button
  - entity: cover.single_garage
    hold_action:
      action: more-info
    name: Single Car Garage
    show_icon: true
    show_name: true
    state_color: true
    tap_action:
      action: toggle
    type: button
title: Garage Doors
type: horizontal-stack

Home Assistant Lovelace Horizontal Stack Card - No Cover

cards:
  - entity: binary_sensor.double_garage_door_sensor
    hold_action:
      action: more-info
    name: Double Car Garage
    show_icon: true
    show_name: true
    state_color: true
    tap_action:
      action: call-service
      service: homeassistant.turn_on
      service_data:
        entity_id: switch.double_garage_door_switch
    type: button
  - entity: binary_sensor.single_garage_door_sensor
    hold_action:
      action: more-info
    name: Single Car Garage
    show_icon: true
    show_name: true
    state_color: true
    tap_action:
      action: call-service
      service: homeassistant.turn_on
      service_data:
        entity_id: switch.single_garage_door_switch
    type: button
title: Garage Doors
type: horizontal-stack

Docker Information

Docker - esphome/esphome:dev docker run -d -v "/LOCAL/PATH/esphome/config:/config" --net=host esphome/esphome:dev

Software

  • ESPHome Flasher - Used to flash initial config to ESP32. Used this utility on a Mac and it required extra drivers installed for serial to USB.
  • Drivers - Installed these drivers to make the Serial port show up when connecting as USB to Mac.

Project Pictures

UI UI UI UI UI UI UI

About

Garage Door Relay and Sensor for two garage doors using ESPHome and integrated to Home Assistant

Topics

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published