Fix spelling mistakes in DTS bindings

dts/bindings/i3c/cdns,i3c.yaml

@@ -23,4 +23,4 @@ properties:
   ibid-thr:
     type: int
     default: 1
-    description: IBI Data Fifo Threashold Value
+    description: IBI Data FIFO Threshold Value

dts/bindings/interrupt-controller/microchip,dmec-ecia-girq.yaml

@@ -9,7 +9,7 @@ properties:
     type: array
     required: true
     description: |
-      Many DEC/MEC periperals interrupt signals are direct capable. The signals are
+      Many DEC/MEC peripherals interrupt signals are direct capable. The signals are
       connected to bits in a GIRQ. Each GIRQ is composed of 5 32-bit registers:
       status(latched or r/w1-c), set-enable, clr-enable, and result (read-only).
       The read-only result register bits are the bitwise AND of status and enable.

dts/bindings/interrupt-controller/sifive,clint0.yaml

@@ -1,7 +1,7 @@
 # Copyright (c) 2022 Nordic Semiconductor ASA
 # SPDX-License-Identifier: Apache-2.0
 
-description: SiFive RISC-V Core-Local Interruptor.
+description: SiFive RISC-V Core-Local Interrupt Controller.
 
 compatible: "sifive,clint0"
 

dts/bindings/ospi/st,stm32-ospi.yaml

@@ -59,7 +59,7 @@ properties:
         - For channel configuration, only the config bits priority and
           periph/mem datasize are used. The periph/mem datasize must be equal,
           0 is a correct value.
-         - There is no Fifo used by this DMA peripheral.
+         - There is no FIFO used by this DMA peripheral.
 
       For example dmas for TX/RX on OSPI
          dmas = <&dma1 5 41 0x10000>;

dts/bindings/pinctrl/adi,max32-pinctrl.yaml

@@ -52,7 +52,7 @@ child-binding:
         * 4 : Alternate Function 4
         In case selected pin function is GPIO, pin is statically configured as
         a plain input/output GPIO. Default configuration is input. Output value
-        can be configured by adding 'ouptut-low' or 'output-high' properties
+        can be configured by adding 'output-low' or 'output-high' properties
         to the pin configuration.
 
         To simplify the usage, macro is available to generate "pinmux" field.

dts/bindings/pinctrl/infineon,xmc4xxx-pinctrl.yaml

@@ -78,7 +78,7 @@ child-binding:
         Encodes port/pin and alternate function. See helper macro XMC4XX_PINMUX_SET().
         Alternate function is only set for output pins; It selects  ALT1-ALT4
         output line in the GPIO element. The alternate function for input pins is
-        handled separately by the peripheral. It is upto the peripheral to configure which
+        handled separately by the peripheral. It is up to the peripheral to configure which
         input pin to use (For example see parameter input-src in infineon,xmc4xxx-uart.yaml).
       required: true
       type: int

dts/bindings/pinctrl/st,stm32-pinctrl.yaml

@@ -70,7 +70,7 @@ child-binding:
         * 17 : GPIO
         In case selected pin function is GPIO, pin is statically configured as
         a plain input/output GPIO. Default configuration is input. Output value
-        can be configured by adding 'ouptut-low' or 'output-high' properties
+        can be configured by adding 'output-low' or 'output-high' properties
         to the pin configuration.
 
         To simplify the usage, macro is available to generate "pinmux" field.

dts/bindings/pinctrl/st,stm32f1-pinctrl.yaml

@@ -73,7 +73,7 @@ child-binding:
         * 2 : Analog
         * 3 : GPIO output
         In case selected pin function is GPIO output, pin is statically configured as
-        a plain output GPIO, which configuration can be set by adding 'ouptut-low' or
+        a plain output GPIO, which configuration can be set by adding 'output-low' or
         'output-high' properties to the pinctrl configuration. Default is output-low.
         - remap: The pin remapping configuration. It allows to assign the pin
         function to a different peripheral. Remain configuration can be:

dts/bindings/regulator/regulator.yaml

@@ -17,7 +17,7 @@ properties:
 
   regulator-init-microvolt:
     type: int
-    description: Voltage set during initialisation
+    description: Voltage set during initialization
 
   regulator-min-microvolt:
     type: int
@@ -33,7 +33,7 @@ properties:
 
   regulator-init-microamp:
     type: int
-    description: Current set during initialisation
+    description: Current set during initialization
 
   regulator-min-microamp:
     type: int
@@ -78,7 +78,7 @@ properties:
     type: int
     description: |
       ramp delay for regulator(in uV/us) For hardware which supports disabling
-      ramp rate, it should be explicitly initialised to zero
+      ramp rate, it should be explicitly initialized to zero
       (regulator-ramp-delay = <0>) for disabling ramp delay.
 
   regulator-enable-ramp-delay:

dts/bindings/retained_mem/zephyr,retained-ram.yaml

@@ -1,7 +1,7 @@
 # Copyright (c) 2023 Nordic Semiconductor ASA
 # SPDX-License-Identifier: Apache-2.0
 
-description: Uninitialised RAM-based retained memory area.
+description: Uninitialized RAM-based retained memory area.
 
 compatible: "zephyr,retained-ram"
 

dts/bindings/rtc/silabs,gecko-stimer.yaml

@@ -8,7 +8,7 @@ description: |
         real-time counter that allows for precise timekeeping.
         The sleeptimer utilizes hardware timer(SYSRTC) to manage ticks
         and timeouts. gecko stimer uses sleeptimer service from Silicon
-        Labs SDK which can run mulitple sw timers using a single counter.
+        Labs SDK which can run multiple sw timers using a single counter.
         The sleeptimer service itself manages the IRQ handling, and the
         gecko stimer driver seamlessly connects to the IRQ utilized by
         the sleeptimer service.

dts/bindings/serial/infineon,xmc4xxx-uart.yaml

@@ -45,8 +45,8 @@ properties:
 
   fifo-tx-size:
     description: |
-      Fifo size used for buffering transmit bytes. A value of 0 implies that
-      the fifo is not used while transmitting. transmitting. If the UART is used in async mode
+      FIFO size used for buffering transmit bytes. A value of 0 implies that
+      the FIFO is not used while transmitting. If the UART is used in async mode
       then fifo-tx-size should be set to 0.
     required: true
     type: int
@@ -61,8 +61,8 @@ properties:
 
   fifo-rx-size:
     description: |
-      Fifo size used for buffering received bytes. A value of 0 implies that
-      the fifo is not used while receiving. If the UART is used in async mode
+      FIFO size used for buffering received bytes. A value of 0 implies that
+      the FIFO is not used while receiving. If the UART is used in async mode
       then fifo-rx-size should be set to 0.
     required: true
     type: int

dts/bindings/watchdog/gd,gd32-fwdgt.yaml

@@ -18,7 +18,7 @@ properties:
       Set timeout value in milliseconds.
       The following equation gives the maximum timeout value
 
-        timeout = (reload + 1) / (peripheral_freqency / prescaler).
+        timeout = (reload + 1) / (peripheral_frequency / prescaler).
 
       where the maximum prescaler = 256 and the maximum reload = 4096.
       The peripheral_frequency uses GD32_LOW_SPEED_IRC_FREQUENCY