Skip to content

Commit

Permalink
Makefile enable even lower power.
Browse files Browse the repository at this point in the history
  • Loading branch information
@kamilsss655
kamilsss655 committed Dec 16, 2023
1 parent 4cbd43c commit f596572
Show file tree
Hide file tree
Showing 2 changed files with 42 additions and 41 deletions.
2 changes: 1 addition & 1 deletion Makefile
View file
Original file line number Diff line number Diff line change
Expand Up @@ -41,7 +41,7 @@ ENABLE_RSSI_BAR := 1
ENABLE_AUDIO_BAR := 1
ENABLE_COPY_CHAN_TO_VFO := 1
ENABLE_SPECTRUM := 1
ENABLE_REDUCE_LOW_MID_TX_POWER := 0
ENABLE_REDUCE_LOW_MID_TX_POWER := 1
ENABLE_BYP_RAW_DEMODULATORS := 0
ENABLE_BLMIN_TMP_OFF := 0
ENABLE_SCAN_RANGES := 1
Expand Down
81 changes: 41 additions & 40 deletions README.md
View file
Original file line number Diff line number Diff line change
Expand Up @@ -93,46 +93,47 @@ us to remove certain firmware features in order to make room in the flash for ot
You'll find the options at the top of "Makefile" ('0' = disable, '1' = enable) ..

```
ENABLE_CLANG := 0 **experimental, builds with clang instead of gcc (LTO will be disabled if you enable this)
ENABLE_SWD := 0 only needed if using CPU's SWD port (debugging/programming)
ENABLE_OVERLAY := 0 cpu FLASH stuff, not needed
ENABLE_LTO := 1 **experimental, reduces size of compiled firmware but might break EEPROM reads (OVERLAY will be disabled if you enable this)
ENABLE_UART := 1 without this you can't configure radio via PC !
ENABLE_AIRCOPY := 0 easier to just enter frequency with butts
ENABLE_FMRADIO := 1 WBFM VHF broadcast band receiver
ENABLE_NOAA := 0 everything NOAA (only of any use in the USA)
ENABLE_VOICE := 0 want to hear voices ?
ENABLE_VOX := 1
ENABLE_ALARM := 0 TX alarms
ENABLE_TX1750 := 0 side key 1750Hz TX tone (older style repeater access)
ENABLE_PWRON_PASSWORD := 0 power-on password stuff
ENABLE_DTMF_CALLING := 1 DTMF calling fuctionality, sending calls, receiving calls, group calls, contacts list etc.
ENABLE_BIG_FREQ := 1 big font frequencies (like original QS firmware)
ENABLE_SMALL_BOLD := 1 bold channel name/no. (when name + freq channel display mode)
ENABLE_KEEP_MEM_NAME := 1 maintain channel name when (re)saving memory channel
ENABLE_WIDE_RX := 1 full 18MHz to 1300MHz RX (though front-end/PA not designed for full range)
ENABLE_TX_WHEN_AM := 0 allow TX (always FM) when RX is set to AM
ENABLE_F_CAL_MENU := 0 enable the radios hidden frequency calibration menu
ENABLE_CTCSS_TAIL_PHASE_SHIFT := 0 standard CTCSS tail phase shift rather than QS's own 55Hz tone method
ENABLE_BOOT_BEEPS := 0 gives user audio feedback on volume knob position at boot-up
ENABLE_SHOW_CHARGE_LEVEL := 1 show the charge level when the radio is on charge
ENABLE_REVERSE_BAT_SYMBOL := 0 mirror the battery symbol on the status bar (+ pole on the right)
ENABLE_NO_CODE_SCAN_TIMEOUT := 1 disable 32-sec CTCSS/DCS scan timeout (press exit butt instead of time-out to end scan)
ENABLE_AM_FIX := 1 dynamically adjust the front end gains when in AM mode to help prevent AM demodulator saturation, ignore the on-screen RSSI level (for now)
ENABLE_AM_FIX_SHOW_DATA := 0 show debug data for the AM fix
ENABLE_SQUELCH_MORE_SENSITIVE := 1 make squelch levels a little bit more sensitive - I plan to let user adjust the values themselves
ENABLE_FASTER_CHANNEL_SCAN := 1 increases the channel scan speed, but the squelch is also made more twitchy
ENABLE_RSSI_BAR := 1 enable a dBm/Sn RSSI bar graph level in place of the little antenna symbols
ENABLE_AUDIO_BAR := 1 experimental, display an audio bar level when TX'ing
ENABLE_COPY_CHAN_TO_VFO := 1 copy current channel into the other VFO. Long press `1 BAND` when in channel mode
ENABLE_SPECTRUM := 1 fagci spectrum analyzer, activated with `F` + `5 NOAA`
ENABLE_REDUCE_LOW_MID_TX_POWER:= 0 makes medium and low power settings even lower
ENABLE_BYP_RAW_DEMODULATORS := 0 additional BYP (bypass?) and RAW demodulation options, proved not to be very useful, but it is there if you want to experiment
ENABLE_BLMIN_TMP_OFF := 0 additional function for configurable buttons that toggles `BLMin` on and off wihout saving it to the EEPROM
ENABLE_SCAN_RANGES := 1 scan range mode for frequency scanning, see wiki for instructions (radio operation -> frequency scanning)
ENABLE_SPECTRUM_COPY_VFO := 1 pressing MENU in spectrum mode will exit and copy current peak frequency to current VFO
ENABLE_CLANG := 0 **experimental, builds with clang instead of gcc (LTO will be disabled if you enable this)
ENABLE_SWD := 0 only needed if using CPU's SWD port (debugging/programming)
ENABLE_OVERLAY := 0 cpu FLASH stuff, not needed
ENABLE_LTO := 1 **experimental, reduces size of compiled firmware but might break EEPROM reads (OVERLAY will be disabled if you enable this)
ENABLE_UART := 1 without this you can't configure radio via PC !
ENABLE_AIRCOPY := 0 easier to just enter frequency with butts
ENABLE_FMRADIO := 1 WBFM VHF broadcast band receiver
ENABLE_NOAA := 0 everything NOAA (only of any use in the USA)
ENABLE_VOICE := 0 want to hear voices ?
ENABLE_VOX := 1
ENABLE_ALARM := 0 TX alarms
ENABLE_TX1750 := 0 side key 1750Hz TX tone (older style repeater access)
ENABLE_PWRON_PASSWORD := 0 power-on password stuff
ENABLE_DTMF_CALLING := 1 DTMF calling fuctionality, sending calls, receiving calls, group calls, contacts list etc.
ENABLE_BIG_FREQ := 1 big font frequencies (like original QS firmware)
ENABLE_SMALL_BOLD := 1 bold channel name/no. (when name + freq channel display mode)
ENABLE_KEEP_MEM_NAME := 1 maintain channel name when (re)saving memory channel
ENABLE_WIDE_RX := 1 full 18MHz to 1300MHz RX (though front-end/PA not designed for full range)
ENABLE_TX_WHEN_AM := 0 allow TX (always FM) when RX is set to AM
ENABLE_F_CAL_MENU := 0 enable the radios hidden frequency calibration menu
ENABLE_CTCSS_TAIL_PHASE_SHIFT := 0 standard CTCSS tail phase shift rather than QS's own 55Hz tone method
ENABLE_BOOT_BEEPS := 0 gives user audio feedback on volume knob position at boot-up
ENABLE_SHOW_CHARGE_LEVEL := 1 show the charge level when the radio is on charge
ENABLE_REVERSE_BAT_SYMBOL := 0 mirror the battery symbol on the status bar (+ pole on the right)
ENABLE_NO_CODE_SCAN_TIMEOUT := 1 disable 32-sec CTCSS/DCS scan timeout (press exit butt instead of time-out to end scan)
ENABLE_AM_FIX := 1 dynamically adjust the front end gains when in AM mode to help prevent AM demodulator saturation, ignore the on-screen RSSI level (for now)
ENABLE_AM_FIX_SHOW_DATA := 0 show debug data for the AM fix
ENABLE_SQUELCH_MORE_SENSITIVE := 1 make squelch levels a little bit more sensitive - I plan to let user adjust the values themselves
ENABLE_FASTER_CHANNEL_SCAN := 1 increases the channel scan speed, but the squelch is also made more twitchy
ENABLE_RSSI_BAR := 1 enable a dBm/Sn RSSI bar graph level in place of the little antenna symbols
ENABLE_AUDIO_BAR := 1 experimental, display an audio bar level when TX'ing
ENABLE_COPY_CHAN_TO_VFO := 1 copy current channel into the other VFO. Long press `1 BAND` when in channel mode
ENABLE_SPECTRUM := 1 fagci spectrum analyzer, activated with `F` + `5 NOAA`
ENABLE_REDUCE_LOW_MID_TX_POWER := 1 makes medium and low power settings even lower
ENABLE_BYP_RAW_DEMODULATORS := 0 additional BYP (bypass?) and RAW demodulation options, proved not to be very useful, but it is there if you want to experiment
ENABLE_BLMIN_TMP_OFF := 0 additional function for configurable buttons that toggles `BLMin` on and off wihout saving it to the EEPROM
ENABLE_SCAN_RANGES := 1 scan range mode for frequency scanning, see wiki for instructions (radio operation -> frequency scanning)
ENABLE_SPECTRUM_COPY_VFO := 1 pressing MENU in spectrum mode will exit and copy current peak frequency to current VFO
ENABLE_SPECTRUM_SHOW_CHANNEL_NAME := 1 shows channel number and channel name of the peak frequency in spectrum
```


Expand Down

0 comments on commit f596572

Please sign in to comment.