Skip to content

RO-copy of the AR488-ESP32 ESP32/Arduino GPIB Interface project on sourcehut

License

Notifications You must be signed in to change notification settings

douardda/AR488-ESP32

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

ESP32-488 ESP32/Arduino based GPIB Interface

The ESP32-488 GPIB controller is an ESP32-based controller for interfacing with IEEE488 GPIB devices via USB using the Arduino developement environment. This project is a friendly fork from the AR488 project aiming at supporting the ESP32 family platform and improving the source code of the firmware. The original AR488 itself was inspired by and has been based on the work originally released by Emanuele Girlando.

This sketch represents a major refactoring of the orignal AR488 source code.

It implements the full set of Prologix ++ commands in both controller and device mode. Secondary GPIB addressing is not yet supported. A number of additional features are provided, for example, a macro feature is provided to allow automation of frequently used command sequences was well as controller and instrument initialisation at startup. Interfacing with SN75160 and SN75161 GPIB transceiver integrated circuits is supported.

Features

All original AR488 features:

  • use Prologix command syntax
  • support most Prologix commands
  • optionnaly support SN7516x transceivers

plus a number of new features:

  • wireless connections (wifi and/or bluetooth, depending on the EPS32 core used),
  • embedded help message
  • run-time configurable wifi connection settings (stored in the nvram),
  • up to 10 run-time editable macros (stored in the nvram), macro 0 being executed at startup
  • ++allspoll command (implement the IEEE-488.2 ALLSPOLL protocol)
  • ++findlstn command (implement the IEEE-488.2 FINDLSTN protocol)
  • ++findrqs command (implement the IEEE-488.2 FINDRQS protocol)
  • ++tct command (implement the IEEE-488 TCT (Take Control) message)

Supported boards and interface design

While targeting the ESP32 platform, this firmware reamains compatible with standard Arduino boards. However, some features are not supported on old boards, and 328p based boards should not be considered as they are very limited in flash and RAM space.

To build an interface, at least one Arduino board will be required to act as the interface hardware. Arduinos provide a low cost alternative to other commercial interfaces. Currently the following boards are supported:

MCU Board Serial Ports Layouts
ESP32 Any UART over USB, Bluetooth, Wifi configurable
ESP32S2 Any UART over USB, Wifi configurable

Generally speaking, any ESP32 based board should work. When choosing a layout, pay attention to pins which have special purpose on the ESP32 as well as pins that are inputs only.

Including the SN7516x chipset into the interface design will naturally add to the cost, but has the advantage of providing the full 48mA drive current capacity regardless of the capability of the board being used, as well as providing proper tri-state output with Hi-Z when the board is powered down. The latter isolates the micro-controller from the GPIB bus when the interface is powered down, preventing GPIB bus communication problems due to 'parasitic power' from signals present on the GPIB bus, thereby allowing the interface to be safely powered down while not in use.

An example design for this configuration is provided here

Unless some form of shield or custom design with integral IEEE488 connector is used, connecting to an instrument will require a 16 core cable and a suitable IEEE488 connector. This can be salvaged from an old GPIB cable or purchased from various electronics parts suppliers. Searching for a 'centronics 24-way connector' sometimes yields better results than searching for 'IEEE 488 connector' or 'GPIB connector'. Details of interface construction and the mapping of Arduino pins to GPIB control signals and data bus are explained in the "Building an AR488 GPIB Interface" section of the AR488-ESP32 Manual.

Commands generally adhere closely to the Prologix syntax, however there are some minor differences, additions and enhancements. Some commands have been enhanced with additional options and a number of new custom commands have been added to provide new features that are not found in the standard Prologix implementation. Details of all commands and features can be found in the Command Reference section of the AR488-ESP32 Manual.

Building the firmware image is using the platformio development environment.

Using the cli flavor of platformio, once installed, building the firmware for a generic ESP32 WRover board is a matter of:

AR488-ESP32$ pio run -e esp32dev
[...]
================================ [SUCCESS] Took 3.39 seconds ================================

Environment    Status    Duration
-------------  --------  ------------
esp32dev       SUCCESS   00:00:03.386
================================ 1 succeeded in 00:00:03.386 ================================

Uploading is a matter of using the command with the extra -t upload option:

AR488-ESP32$ pio run -e esp32dev -t upload

Once uploaded, the firmware should respond to the ++ver command with its version information.

Please see the documentation for more details on the configuration and compilation of the firmware for a given ESP32 board.

Wireless Communication

Depending on the ESP32 board you are using, it may come with support for wifi, bluetooth or both. You can enable or disable support for wireless communication using compile-time options defined in the platformio.ini file.

See this documentation for more details on how to use wireless communication with the AR488-ESP32.

Obtaining support

In the event that a problem is found, this can be logged via the Issues feature on the AR488-ESP32 sourcehut page. Please provide at minimum:

  • the firmware version number
  • the type of board being used
  • the make and model of instrument you are trying to control
  • a description of the issue including;
  • what steps are required to reproduce the issue

Acknowledgements

Emanuelle Girlando Original project for the Arduino Uno
Luke Mester Testing of original Uno/Nano verions against Prologix
Artag Porting to the Arduino Micro (32u4) board
Tom DG8SAQ Plotting and printing
Twilight-Logic Author and maintainer of the AR488 project

Also, thank you to all the contributors to the AR488 EEVblog thread for their suggestions and support.

The original work by Emanuele Girlando is found here: http://egirland.blogspot.com/2014/03/arduino-uno-as-usb-to-gpib-controller.html

About

RO-copy of the AR488-ESP32 ESP32/Arduino GPIB Interface project on sourcehut

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • C++ 88.6%
  • C 11.4%