fraqture

An interactive art framework that takes inputs from social media, maps them to the interactive parts of a drawing, and renders the art. The platform consists of a 50" TV display driven by Clojure's Quil library outlined with 540 DotStar LEDs driven by a Teensy 3.2.

Exhibitions

Come see fraqture live!

You can find Fraqture today in the 21C storefront window in downtown Durham, NC.

March 14-16th - New Orleans Entrepreneurs Week
Now - Downtown Durham

Usage

lein run <drawing name>

For examples of what each of the drawings does, check out the gifs in examples.md. Start by trying lein run cycle.

Hardware

The Fraqture Project uses two custom-build LED panels with 270 individually addressable LEDs each to extend our canvas out from the screen. We are using a Teensy 3.2 to receive commands over a serial connection and use them to refresh the panels. The sections below discusses how to connect and issue commands to the panels.

Reset Communications

The LED serial communication is a basic state machine. When a device connects to the panel driver, it is impossible to know whether it is in the default state or not. To reset the state machine of the panel driver, simply wait 2 seconds in between messages and the state will be reset.

LED Commands

All LED panel commands follow the same structure, where the payload is strictly packed and all numbers larger than 8 bits are packed little endian.

1 BYTE        0-7 BYTES
+------------+-----------------+
| COMMAND ID | COMMAND PAYLOAD |
+------------+-----------------+

New commands can easily be added using the terminal_attach(terminal_t *term, terminal_cmd_t *cmd) function found in arduino/strobe/terminal.c.

Refresh Pixels

This command will refresh the LED array. This allows you to do multiple paint operations without eating the cost of refreshing the array after each one.

Command ID: R

Clear Pixels

This command will clear the LED arrays. This command has no payload.

Command ID: S

Window Pixels

This command will paint a window of pixels.

Command ID: W

Payload (in order):

u8 row-start: the starting row for the window
u8 col-start: the starting column for the window
u8 row-end: the starting row for the window
u8 col-end: the ending row for the window
u8 r: the brightness of the red LED in the pixel
u8 g: the brightness of the green LED in the pixel
u8 b: the brightness of the blue LED in the pixel

Set Pixel

This command will set an individual pixel.

Command ID: S

Payload (in order):

u16 index: the index of the pixel. The top left is pixel 0, and then it reads like a book.
u8 r: the brightness of the red LED in the pixel
u8 g: the brightness of the green LED in the pixel
u8 b: the brightness of the blue LED in the pixel

Requirements

Install Java JRE or JDK from Oracle's website.
brew install leiningen (or install it for your OS using these instructions)
Imagesnap brew install imagesnap (or install it from here)

System Setup

The overall diagram of how the LED controller, LED panels, power supply, and Mac Mini all interact can be seen below:

Since LED data is a serial stream, it originates by the Mac Mini's program sending data to the LED controller, which then sends it out to the 540 LEDs using SPI. The individual wires that need to be connected can be found below.

For the panel connections, the diagram shows a closeup of the screw terminals found on the backs of the panels. The panels should be positioned so that the screw terminals are in the lower-left of each panel. A legend for these connectors is below:

Line - Wire to another component.
X - Internal panel connection; leave connected.
N/C - No connection.

LED Controller

Panel 1 (Top)

Panel 2 (Bottom)

Power Supply Unit (PSU)

BrandonMathis/fraqture

ErrorLooks like something went wrong!

About

Resources

Uh oh!

Stars

Watchers

Forks

Releases

Packages 0

Languages

Error
Looks like something went wrong!

Packages