Skip to content

AmyPhung/portal_turret

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

35 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

POE Portal Turret

This repository contains code for a portal turret that shoots foam balls at a target.

Architecture

V1:

  • Used a raspi as main computing device
  • Used a picam to detect people
  • Was pretty slow (~3s lag) for detecting people with full resolution images, was alright with very coarse images (~0.5s lag)

V2:

  • Uses an Intel Euclid as main computing device

One-Time Setup

Local

On your computer, you will need:

  • ROS Kinetic
  • Ubuntu 16 (strongly recommended)

Assuming you have the proper dependencies installed, to set up this repository

Euclid

To get the most recent version of the code on the Euclid, follow these instructions:

On the Euclid:

  1. cd /intel/euclid/euclid_ws/src
  2. git clone https://github.com/AmyPhung/portal_turret.git
  3. cd /intel/euclid/euclid_ws
  4. catkin_make

Connecting to the Euclid

In order to connect to the Euclid via ssh, follow the following instructions:

  • Plug in the Euclid and power it on
  • Wait until the network EUCLID_50AB shows up and connect to it
  • SSH into the Euclid using the command ssh [email protected]. Password is still the default.
  • On your local computer, you should be able to go to http://10.42.0.1/ in a web browser and see an interface to work with the Euclid.
  • On your local computer, run the following commands to properly configure ROS (note that this will only apply to the terminal you run them in - you will need to run this for each terminal you plan to use to interface with the Euclid)
export ROS_MASTER_URI=http://10.42.0.1:11311
export ROS_IP=10.42.0.219
# Note: The ip address you use for the ROS_IP should be the output of the command "ifconfig" on your local machine

Uploading code via SSH

It is much more convenient to upload code remotely to the Arduino by using the Euclid rather than manually having to plug your laptop into the Arduino and using the IDE every time you just want to make a small code change. I've documented this setup process here for future reference.

One-Time Setup (reference)

  1. sudo apt install arduino
  2. pip install pyserial
  3. cd ~/Documents
  4. git clone https://github.com/sudar/Arduino-Makefile.git
  5. cd /usr/share/arduino/libraries
  6. sudo git clone https://github.com/adafruit/Adafruit_Motor_Shield_V2_Library.git

Usage (Uploading new changes)

To upload new code:

  1. cd /intel/euclid/euclid_ws/src/portal_turret/src/turret_base
  2. make upload (Note: to just compile code, you can also just use make)

Running Code

Assuming everything is set up properly you should be able to do the following:

On the Euclid:

  • roslaunch portal_turret bringup.launch
  • Go to http://10.42.0.1/ and activate the PersonView Scenario under the Scenarios tab

On your computer

  • Follow the connect to Euclid instructions
  • On your computer run rosrun portal_turret GuiWindow.py

Other ROS commands

On either machine, you should be able to use ROS commands. Some useful commands are listed below:

  • rostopic list - shows all available data currently being published
  • rostopic echo /topic_name - prints out data being published to topic
  • rosnode list - shows running nodes
  • rosnode info /node_name - prints out data type of node and publishers/subscribers associated with node

Deprecated Notes (refers to Pi)

Raspi Notes

  • Currently using the Raspberry Pi Model B+ V1.2
  • password is portal2rocks
  • connected to olin-devices
  • ssh -X [email protected]
  • To shutdown, sudo shutdown -h now

Raspi Camera notes

  • In sudo raspi-config, enable I2C and camera under Peripherials option

Setting up remote code upload on the Pi

On the raspberry pi:

  1. sudo apt install arduino
  2. pip install pyserial
  3. cd ~/Documents
  4. git clone https://github.com/sudar/Arduino-Makefile.git
  5. cd /usr/share/arduino/libraries
  6. sudo git clone https://github.com/adafruit/Adafruit_Motor_Shield_V2_Library.git

References

Other Notes

Misc notes to be sorted through

ssid=hotspot #ssid=OLIN-DEVICES #ROS_MASTER_URI:http://10.0.2.15:11311 ROS_MASTER_URI:http://10.42.0.1:11311 ConnectivityMonitor=55516 LEDServer=38298 SoundServer=43922

After connecting (shouldn't need this): sudo service oobe-init restart-oobe

settings.ini File:

ssid=hotspot ROSMasterURI=http://10.42.0.1:11311 ConnectivityMonitor=55516 LEDServer=38298 SoundServer=43922

On laptop: export ROS_MASTER_URI=http://10.42.0.1:11311 export ROS_IP=http://10.42.0.1:11311

/camera/color/image_raw/compressed /camera/fisheye/image_raw/compressed /camera/imu_raw /camera/ir2/image_raw/compressed /camera/ir/image_raw/compressed /camera/depth/points /camera/depth/image_raw

/camera/color/image_raw/compressed /camera/fisheye/image_raw/compressed /camera/imu_raw /camera/ir2/image_raw/compressed /camera/ir/image_raw/compressed /camera/depth/points /camera/depth/image_raw

Notes: Why new sensors? Why ROS? Why new structure?

About

Code for a robotic turret replica from the Portal game series.

Resources

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published