-
Notifications
You must be signed in to change notification settings - Fork 0
/
bme280.py
executable file
·153 lines (123 loc) · 4.56 KB
/
bme280.py
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
#!/usr/bin/env python3
# https://www.raspberrypi-spy.co.uk/2016/07/using-bme280-i2c-temperature-pressure-sensor-in-python/
import smbus
import time
from ctypes import c_short
from ctypes import c_byte
from ctypes import c_ubyte
DEVICE = 0x76 # Default device I2C address
bus = smbus.SMBus(1) # Rev 2 Pi, Pi 2 & Pi 3 uses bus 1
# Rev 1 Pi uses bus 0
def getShort(data, index):
# return two bytes from data as a signed 16-bit value
return c_short((data[index+1] << 8) + data[index]).value
def getUShort(data, index):
# return two bytes from data as an unsigned 16-bit value
return (data[index+1] << 8) + data[index]
def getChar(data,index):
# return one byte from data as a signed char
result = data[index]
if result > 127:
result -= 256
return result
def getUChar(data,index):
# return one byte from data as an unsigned char
result = data[index] & 0xFF
return result
def readBME280ID(addr=DEVICE):
# Chip ID Register Address
REG_ID = 0xD0
(chip_id, chip_version) = bus.read_i2c_block_data(addr, REG_ID, 2)
return (chip_id, chip_version)
def readBME280All(addr=DEVICE):
# Register Addresses
REG_DATA = 0xF7
REG_CONTROL = 0xF4
REG_CONFIG = 0xF5
REG_CONTROL_HUM = 0xF2
REG_HUM_MSB = 0xFD
REG_HUM_LSB = 0xFE
# Oversample setting - page 27
OVERSAMPLE_TEMP = 2
OVERSAMPLE_PRES = 2
MODE = 1
# Oversample setting for humidity register - page 26
OVERSAMPLE_HUM = 2
bus.write_byte_data(addr, REG_CONTROL_HUM, OVERSAMPLE_HUM)
control = OVERSAMPLE_TEMP<<5 | OVERSAMPLE_PRES<<2 | MODE
bus.write_byte_data(addr, REG_CONTROL, control)
# Read blocks of calibration data from EEPROM
# See Page 22 data sheet
cal1 = bus.read_i2c_block_data(addr, 0x88, 24)
cal2 = bus.read_i2c_block_data(addr, 0xA1, 1)
cal3 = bus.read_i2c_block_data(addr, 0xE1, 7)
# Convert byte data to word values
dig_T1 = getUShort(cal1, 0)
dig_T2 = getShort(cal1, 2)
dig_T3 = getShort(cal1, 4)
dig_P1 = getUShort(cal1, 6)
dig_P2 = getShort(cal1, 8)
dig_P3 = getShort(cal1, 10)
dig_P4 = getShort(cal1, 12)
dig_P5 = getShort(cal1, 14)
dig_P6 = getShort(cal1, 16)
dig_P7 = getShort(cal1, 18)
dig_P8 = getShort(cal1, 20)
dig_P9 = getShort(cal1, 22)
dig_H1 = getUChar(cal2, 0)
dig_H2 = getShort(cal3, 0)
dig_H3 = getUChar(cal3, 2)
dig_H4 = getChar(cal3, 3)
dig_H4 = (dig_H4 << 24) >> 20
dig_H4 = dig_H4 | (getChar(cal3, 4) & 0x0F)
dig_H5 = getChar(cal3, 5)
dig_H5 = (dig_H5 << 24) >> 20
dig_H5 = dig_H5 | (getUChar(cal3, 4) >> 4 & 0x0F)
dig_H6 = getChar(cal3, 6)
# Wait in ms (Datasheet Appendix B: Measurement time and current calculation)
wait_time = 1.25 + (2.3 * OVERSAMPLE_TEMP) + ((2.3 * OVERSAMPLE_PRES) + 0.575) + ((2.3 * OVERSAMPLE_HUM)+0.575)
time.sleep(wait_time/1000) # Wait the required time
# Read temperature/pressure/humidity
data = bus.read_i2c_block_data(addr, REG_DATA, 8)
pres_raw = (data[0] << 12) | (data[1] << 4) | (data[2] >> 4)
temp_raw = (data[3] << 12) | (data[4] << 4) | (data[5] >> 4)
hum_raw = (data[6] << 8) | data[7]
#Refine temperature
var1 = ((((temp_raw>>3)-(dig_T1<<1)))*(dig_T2)) >> 11
var2 = (((((temp_raw>>4) - (dig_T1)) * ((temp_raw>>4) - (dig_T1))) >> 12) * (dig_T3)) >> 14
t_fine = var1+var2
temperature = float(((t_fine * 5) + 128) >> 8);
# Refine pressure and adjust for temperature
var1 = t_fine / 2.0 - 64000.0
var2 = var1 * var1 * dig_P6 / 32768.0
var2 = var2 + var1 * dig_P5 * 2.0
var2 = var2 / 4.0 + dig_P4 * 65536.0
var1 = (dig_P3 * var1 * var1 / 524288.0 + dig_P2 * var1) / 524288.0
var1 = (1.0 + var1 / 32768.0) * dig_P1
if var1 == 0:
pressure=0
else:
pressure = 1048576.0 - pres_raw
pressure = ((pressure - var2 / 4096.0) * 6250.0) / var1
var1 = dig_P9 * pressure * pressure / 2147483648.0
var2 = pressure * dig_P8 / 32768.0
pressure = pressure + (var1 + var2 + dig_P7) / 16.0
# Refine humidity
humidity = t_fine - 76800.0
humidity = (hum_raw - (dig_H4 * 64.0 + dig_H5 / 16384.0 * humidity)) * (dig_H2 / 65536.0 * (1.0 + dig_H6 / 67108864.0 * humidity * (1.0 + dig_H3 / 67108864.0 * humidity)))
humidity = humidity * (1.0 - dig_H1 * humidity / 524288.0)
if humidity > 100:
humidity = 100
elif humidity < 0:
humidity = 0
return temperature/100.0,pressure/100.0,humidity
def main():
(chip_id, chip_version) = readBME280ID()
print("Chip ID :", chip_id)
print("Version :", chip_version)
temperature,pressure,humidity = readBME280All()
print("Temperature : ", temperature, "C")
print("Pressure : ", pressure, "hPa")
print("Humidity : ", humidity, "%")
if __name__=="__main__":
main()