You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
DRAM: 64 MiB
Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:
EMMC/MMC/SD controller initialization.
MMC/SD Card:
MID: 0x3
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7580M Bytes (High Capacity)
Name: "SL08G"
Chip Type: SD
Version: 2.0
Speed: 50000000Hz
Bus Width: 4bit
Boot Addr: 0 Bytes
In: serial
Out: serial
Err: serial
device name mmc!
Interface: MMC
Device 0: Vendor: Man 035344 Snr 8564417a Rev: 8.0 Prod: SL08G
Type: Removable Hard Disk
Capacity: 7580.0 MB = 7.4 GB (15523840 x 512)
Partition 1: Filesystem: FAT32 "NO NAME "
reading ezviz.dav
Find 1 packet
file_pos is 0x81000098 app.img checksum is fail
checksum is 682704412, but file original checksum is 681896039
update file startOffset = 152
update file len = 5300224
update_single_file fail
Net: No ethernet found.
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit Ctrl+u to stop autoboot: 0
load kernel to 0x80007fc0 ...
check backup upgrade flag
Done!
Booting kernel from Legacy Image at 80007fc0 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2445872 Bytes = 2.3 MiB
Load Address: 80008000
Entry Point: 80008000
XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.22.1 (2017-08-04 12:25:23 CST)
ifconfig: SIOCGIFFLAGS: No such device
mount: mounting /dev/mtdblock5 on /mnt failed: Invalid argument
APP partition is broken!
cp: can't stat '/mnt/initrun.sh': No such file or directory
No initrun.sh on flash!
umount: can't umount /mnt: Invalid argument
Not find initrun.sh!
/ #
The text was updated successfully, but these errors were encountered:
See in bold below:
System startup
U-Boot 2010.06-19073 (Jun 15 2017 - 14:11:13)
DRAM: 64 MiB
Check Flash Memory Controller v100 ... Found
SPI Nor(cs 0) ID: 0xc2 0x20 0x18
Block:64KB Chip:16MB Name:"MX25L128XX"
SPI Nor total size: 16MB
MMC:
EMMC/MMC/SD controller initialization.
MMC/SD Card:
MID: 0x3
Read Block: 512 Bytes
Write Block: 512 Bytes
Chip Size: 7580M Bytes (High Capacity)
Name: "SL08G"
Chip Type: SD
Version: 2.0
Speed: 50000000Hz
Bus Width: 4bit
Boot Addr: 0 Bytes
In: serial
Out: serial
Err: serial
device name mmc!
Interface: MMC
Device 0: Vendor: Man 035344 Snr 8564417a Rev: 8.0 Prod: SL08G
Type: Removable Hard Disk
Capacity: 7580.0 MB = 7.4 GB (15523840 x 512)
Partition 1: Filesystem: FAT32 "NO NAME "
reading ezviz.dav
Find 1 packet
file_pos is 0x81000098
app.img checksum is fail
checksum is 682704412, but file original checksum is 681896039
update file startOffset = 152
update file len = 5300224
update_single_file fail
Net: No ethernet found.
(Re)start USB...
USB: scanning bus for devices... 1 USB Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
Hit Ctrl+u to stop autoboot: 0
load kernel to 0x80007fc0 ...
check backup upgrade flag
Done!
Booting kernel from Legacy Image at 80007fc0 ...
Image Name: Linux-3.4.35
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2445872 Bytes = 2.3 MiB
Load Address: 80008000
Entry Point: 80008000
XIP Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
init started: BusyBox v1.22.1 (2017-08-04 12:25:23 CST)
ifconfig: SIOCGIFFLAGS: No such device
mount: mounting /dev/mtdblock5 on /mnt failed: Invalid argument
APP partition is broken!
cp: can't stat '/mnt/initrun.sh': No such file or directory
No initrun.sh on flash!
umount: can't umount /mnt: Invalid argument
Not find initrun.sh!
/ #
The text was updated successfully, but these errors were encountered: