-
Notifications
You must be signed in to change notification settings - Fork 28
/
T-Beam_V10_OLED_SH1106_STRATUX_BT
87 lines (66 loc) · 4.54 KB
/
T-Beam_V10_OLED_SH1106_STRATUX_BT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
#define DEFAULT_AcftType 8 // [0..15] default aircraft-type: Powered Aircraft
#define DEFAULT_GeoidSepar 40 // [m]
#define DEFAULT_CONbaud 115200
#define DEFAULT_PPSdelay 100
#define DEFAULT_FreqPlan 0
#define DEFAULT_DispPage 3 // Fab501 Page to Display After Boot or Reset
// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025
// #define WITH_HELTEC_V2 // HELTEC module v2
// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output
// #define WITH_TBEAM // T-Beam module
#define WITH_TBEAM_V10 // T-Beam module
// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker
// #define WITH_FollowMe // by Avionix
// #define WITH_ILI9341 // 320x240 M5stack
// #define WITH_ST7789 // IPS 240x240 ST7789
// #define WITH_TFT_LCD // TFT LCD
// #define WITH_OLED // OLED display on the I2C: some TTGO modules are without OLED display
// #define WITH_OLED2 // 2nd OLED display, I2C address next higher
#define WITH_U8G2_OLED // I2C OLED through the U8g2 library
#define WITH_U8G2_SH1106 // correct controller for the bigger OLED
// #define WITH_U8G2_FLIP // flip the OLED screen (rotate by 180deg)
#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95
// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button
#define WITH_AXP // with AXP192 power controller (T-BEAM V1.0)
// #define WITH_BQ // with BQ24295 power controller (FollowMe)
// #define WITH_LED_RX
// #define WITH_LED_TX
// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF
#define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync.
#define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode
#define WITH_GPS_UBX // GPS understands UBX
// #define WITH_GPS_MTK // GPS understands MTK
// #define WITH_GPS_SRF
// #define WITH_MAVLINK
#define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS
#define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS
// #define WITH_BMP180 // BMP180 pressure sensor
// #define WITH_BMP280 // BMP280 pressure sensor
#define WITH_BME280 // BMP280 with humidity (but still works with BMP280)
// #define WITH_MS5607 // MS5607 pressure sensor
// #define WITH_MS5611 // MS5611 pressure sensor
// #define WITH_BMX055 // BMX055 magnetic and IMU sensor
// #define WITH_LORAWAN // LoRaWAN connectivity
// #define WITH_FANET // FANET transmission and reception
#define WITH_PAW // Add PAW transmission
#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000
// #define WITH_POGNT
// #define WITH_GDL90
// #define WITH_PGAV5
#define WITH_LOOKOUT
#define WITH_CONFIG // interpret the console input: $POGNS to change parameters
#define WITH_BEEPER // with digital buzzer
// #define WITH_SOUND // with analog sound produced by DAC on pin 25
// #define WITH_KNOB
// #define WITH_VARIO
// #define WITH_SD // use the SD card in SPI mode and FAT file system
#define WITH_SPIFFS // use SPIFFS file system in Flash
// #define WITH_SPIFFS_FAT
#define WITH_LOG // log own positions and other received to SPIFFS
// #define WITH_SDLOG // log own position and other data to uSD card
#define WITH_STRATUX
#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link
#define WITH_WIFI // attempt to connect to the wifi router for uploading the log files
// #define WITH_AP // Open Access Point MOde
#define WITH_HTTP // Open Web Interface
// #define WITH_ENCRYPT // Encrypt (optionally) the position