刷了后显示无法识别闪存，有没有办法解决

[hxbhxb2001]

设备 小米 cr8809 电信定制版 M79 B版

U-Boot 2016.01 (Dec 14 2022 - 10:32:35 +0800)

DRAM: smem ram ptable found: ver: 1 len: 4
256 MiB
NAND: QPIC controller support serial NAND
ID = 81c881c8
Vendor = c8
Device = 81
qpic_nand_read_id_serial : No serial Nand device found in table.
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: sdhci: Node Not found, skipping initialization

*** Warning - readenv() failed, using default environment

现在刷不了uboot TTL 启动的UBOOT 识别闪存错误，这个怎么解决

TTL TFTP 可以上传文件 ，但只要执行 FLASH xx 写入就会卡死，需要拔电源

[hxbhxb2001]

Xshell 8 (Build 0069)
Copyright (c) 2024 NetSarang Computer, Inc. All rights reserved.

Type `help' to learn how to use Xshell prompt.
[C:~]$

Connecting to COM4...
Connected.

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00064
S - IMAGE_VARIANT_STRING=MAACANAZA
S - OEM_IMAGE_VERSION_STRING=node-sh-08
S - Boot Config, 0x000002c5
B - 127 - PBL, Start
B - 1560 - bootable_media_detect_entry, Start
B - 3654 - bootable_media_detect_success, Start
B - 3658 - elf_loader_entry, Start
B - 8840 - auth_hash_seg_entry, Start
B - 9200 - auth_hash_seg_exit, Start
B - 104203 - elf_segs_hash_verify_entry, Start
B - 175389 - PBL, End
B - 144173 - SBL1, Start
B - 205021 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4
B - 213317 - clock_init, Start
D - 7411 - clock_init, Delta
B - 220881 - boot_flash_init, Start
B - 221003 - lsy--->Nov 23 2021, 11:03:10

B - 229878 - lsy--->Nov 23 2021, 11:03:10

D - 25711 - boot_flash_init, Delta
B - 246653 - boot_config_data_table_init, Start
D - 4666 - boot_config_data_table_init, Delta - (575 Bytes)
B - 254400 - Boot Setting : 0x00020618
B - 260744 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:2
B - 267485 - sbl1_ddr_set_params, Start
B - 268918 - Pre_DDR_clock_init, Start
B - 274774 - Pre_DDR_clock_init, End
B - 916647 - do ddr sanity test, Start
D - 30 - do ddr sanity test, Delta
B - 921313 - Image Load, Start
D - 245373 - QSEE Image Loaded, Delta - (578956 Bytes)
B - 1167509 - Image Load, Start
D - 13969 - DEVCFG Image Loaded, Delta - (13592 Bytes)
B - 1181509 - Image Load, Start
D - 192211 - APPSBL Image Loaded, Delta - (458566 Bytes)
B - 1373781 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 1380247 - SBL1, End
D - 1238727 - SBL1, Delta
S - Flash Throughput, 2435 KB/s (1052361 Bytes, 432055 us)
S - DDR Frequency, 800 MHz
S - Core 0 Frequency, 800 MHz

U-Boot 2016.01 (Dec 14 2022 - 10:32:35 +0800)

DRAM: smem ram ptable found: ver: 1 len: 4
256 MiB
NAND: QPIC controller support serial NAND
ID = 81c881c8
Vendor = c8
Device = 81
qpic_nand_read_id_serial : No serial Nand device found in table.
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: sdhci: Node Not found, skipping initialization

*** Warning - readenv() failed, using default environment

PCI Link Intialized
In: serial@78AF000
Out: serial@78AF000
Err: serial@78AF000
machid: 8040002
ART partition read failed..
get jx_key_gpio fdt offset error -1
Hit any key to stop autoboot: 0

Net: cmbblk is stable 5
ART partition read failed..
MAC0 addr:0:11:22:33:44:55
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:0:11:22:33:44:56
GMAC1:Invalid PHY ID
eth0, eth1
IPQ5018# sf write
No SPI flash selected. Please run `sf probe'
IPQ5018# sf probe
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
Failed to initialize SPI flash at 0:0
IPQ5018# nand erase.part firmware

no devices available
IPQ5018# sf erase oxo
No SPI flash selected. Please run sf probe' IPQ5018# sf read ox80000000 No SPI flash selected. Please run sf probe'
IPQ5018# reset
resetting ...

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00064
S - IMAGE_VARIANT_STRING=MAACANAZA
S - OEM_IMAGE_VERSION_STRING=node-sh-08
S - Boot Config, 0x000002c5
B - 127 - PBL, Start
B - 1560 - bootable_media_detect_entry, Start
B - 3655 - bootable_media_detect_success, Start
B - 3659 - elf_loader_entry, Start
B - 8825 - auth_hash_seg_entry, Start
B - 9185 - auth_hash_seg_exit, Start
B - 104060 - elf_segs_hash_verify_entry, Start
B - 175245 - PBL, End
B - 144052 - SBL1, Start
B - 204929 - GCC [RstStat:0x10, RstDbg:0x500100] WDog Stat : 0x4
B - 213408 - clock_init, Start
D - 7411 - clock_init, Delta
B - 221003 - boot_flash_init, Start
B - 221125 - lsy--->Nov 23 2021, 11:03:10

B - 229817 - lsy--->Nov 23 2021, 11:03:10

D - 25376 - boot_flash_init, Delta
B - 246440 - boot_config_data_table_init, Start
D - 4666 - boot_config_data_table_init, Delta - (575 Bytes)
B - 254187 - Boot Setting : 0x00020618
B - 260561 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:2
B - 267271 - sbl1_ddr_set_params, Start
B - 268705 - Pre_DDR_clock_init, Start
B - 274561 - Pre_DDR_clock_init, End
B - 916433 - do ddr sanity test, Start
D - 30 - do ddr sanity test, Delta
B - 921100 - Image Load, Start
D - 245403 - QSEE Image Loaded, Delta - (578956 Bytes)
B - 1167326 - Image Load, Start
D - 13969 - DEVCFG Image Loaded, Delta - (13592 Bytes)
B - 1181326 - Image Load, Start
D - 192211 - APPSBL Image Loaded, Delta - (458566 Bytes)
B - 1373598 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 1380064 - SBL1, End
D - 1238513 - SBL1, Delta
S - Flash Throughput, 2435 KB/s (1052361 Bytes, 432177 us)
S - DDR Frequency, 800 MHz
S - Core 0 Frequency, 800 MHz

U-Boot 2016.01 (Dec 14 2022 - 10:32:35 +0800)

DRAM: smem ram ptable found: ver: 1 len: 4
256 MiB
NAND: QPIC controller support serial NAND
ID = 81c881c8
Vendor = c8
Device = 81
qpic_nand_read_id_serial : No serial Nand device found in table.
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: sdhci: Node Not found, skipping initialization

*** Warning - readenv() failed, using default environment

PCI Link Intialized
In: serial@78AF000
Out: serial@78AF000
Err: serial@78AF000
machid: 8040002
ART partition read failed..
get jx_key_gpio fdt offset error -1
Hit any key to stop autoboot: 0
Device nand0 not found!
invalid mtd device 'nand0'
Error initializing mtdparts!

Net: cmbblk is stable 5
ART partition read failed..
MAC0 addr:0:11:22:33:44:55
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:0:11:22:33:44:56
GMAC1:Invalid PHY ID
eth0, eth1

Net: cmbblk is stable 5
ART partition read failed..
MAC0 addr:0:11:22:33:44:55
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:0:11:22:33:44:56
GMAC1:Invalid PHY ID
, eth0, eth1
IPQ5018#

Connection closed.

Disconnected from remote host(新建会话) at 16:20:10.

Type `help' to learn how to use Xshell prompt.
[C:~]$

Connecting to COM4...
Connected.

reset
resetting ...

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1.1-00064
S - IMAGE_VARIANT_STRING=MAACANAZA
S - OEM_IMAGE_VERSION_STRING=node-sh-08
S - Boot Config, 0x000002c5
B - 127 - PBL, Start
B - 1560 - bootable_media_detect_entry, Start
B - 3655 - bootable_media_detect_success, Start
B - 3659 - elf_loader_entry, Start
B - 8830 - auth_hash_seg_entry, Start
B - 9189 - auth_hash_seg_exit, Start
B - 104089 - elf_segs_hash_verify_entry, Start
B - 175275 - PBL, End
B - 144082 - SBL1, Start
B - 204929 - GCC [RstStat:0x10, RstDbg:0x500100] WDog Stat : 0x4
B - 213439 - clock_init, Start
D - 7411 - clock_init, Delta
B - 221003 - boot_flash_init, Start
B - 221125 - lsy--->Nov 23 2021, 11:03:10

B - 229817 - lsy--->Nov 23 2021, 11:03:10

D - 25345 - boot_flash_init, Delta
B - 246409 - boot_config_data_table_init, Start
D - 4666 - boot_config_data_table_init, Delta - (575 Bytes)
B - 254156 - Boot Setting : 0x00020618
B - 260531 - CDT version:2,Platform ID:8,Major ID:4,Minor ID:0,Subtype:2
B - 267271 - sbl1_ddr_set_params, Start
B - 268705 - Pre_DDR_clock_init, Start
B - 274530 - Pre_DDR_clock_init, End
B - 916403 - do ddr sanity test, Start
D - 61 - do ddr sanity test, Delta
B - 921069 - Image Load, Start
D - 245373 - QSEE Image Loaded, Delta - (578956 Bytes)
B - 1167296 - Image Load, Start
D - 13938 - DEVCFG Image Loaded, Delta - (13592 Bytes)
B - 1181295 - Image Load, Start
D - 192181 - APPSBL Image Loaded, Delta - (458566 Bytes)
B - 1373537 - QSEE Execution, Start
D - 30 - QSEE Execution, Delta
B - 1380003 - SBL1, End
D - 1238422 - SBL1, Delta
S - Flash Throughput, 2435 KB/s (1052361 Bytes, 432056 us)
S - DDR Frequency, 800 MHz
S - Core 0 Frequency, 800 MHz

U-Boot 2016.01 (Dec 14 2022 - 10:32:35 +0800)

DRAM: smem ram ptable found: ver: 1 len: 4
256 MiB
NAND: QPIC controller support serial NAND
ID = 81c881c8
Vendor = c8
Device = 81
qpic_nand_read_id_serial : No serial Nand device found in table.
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: sdhci: Node Not found, skipping initialization

*** Warning - readenv() failed, using default environment

PCI Link Intialized
In: serial@78AF000
Out: serial@78AF000
Err: serial@78AF000
machid: 8040002
ART partition read failed..
get jx_key_gpio fdt offset error -1
Hit any key to stop autoboot: 0
Device nand0 not found!
invalid mtd device 'nand0'
Error initializing mtdparts!

Net: cmbblk is stable 5
ART partition read failed..
MAC0 addr:0:11:22:33:44:55
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:0:11:22:33:44:56
GMAC1:Invalid PHY ID
eth0, eth1

Net: cmbblk is stable 5
ART partition read failed..
MAC0 addr:0:11:22:33:44:55
PHY ID1: 0x4d
PHY ID2: 0xd0c0
MAC1 addr:0:11:22:33:44:56
GMAC1:Invalid PHY ID
, eth0, eth1
IPQ5018# nand probe 0
Unknown command 'nand' - try 'help'
IPQ5018# setenv spi_max_hz 24000000
IPQ5018# setenv spi_max_hz 24000000
IPQ5018# sf probe 0 0 24000000
SPI error: unsupported SPI mode 603979776
Failed to initialize SPI flash at 0:0
IPQ5018#

以上是完整TTL 启动信息。

改本地IP 192.168.10.101 可以上传文件

IPQ5018# tftpboot MIBIB.bin
Trying eth0
eth0 up Speed :100 Full duplex
Using eth0 device
TFTP from server 192.168.10.101; our IP address is 192.168.10.1
Filename 'MIBIB.bin'.
Load address: 0x44000000
Loading: *
Got TFTP_OACK: TFTP remote port: changes from 69 to 54424
####################################
2.6 MiB/s
done
Bytes transferred = 524288 (80000 hex)
IPQ5018#
IPQ5018#

再使用 flash 0:MIBIB

IPQ5018# flash 0:MIBIB
do flash

ERROR ### Please RESET the board

卡死了。 只能拔电重插。 无法刷写flash

[hxbhxb2001]

闪存颗粒是 5F1GM7REY1G