MultiLine.h

/*
 * MultiLine.h
 *
 * Copyright 2012-2015 Tim Barrass.
 *
 * This file is part of Mozzi.
 *
 * Mozzi is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
 *
 */

#ifndef MultiLine_H_
#define MultiLine_H_

#if ARDUINO >= 100
 #include "Arduino.h"
#else
 #include "WProgram.h"
#endif
#include "Line.h"
#include "mozzi_fixmath.h"


/** A simple MultiLine envelope generator.  This implementation has separate update() and next()
methods, where next() interpolates values between each update().
The "normal" way to use this would be with update() in updateControl(), where it calculates a new internal state each control step,
and then next() is in updateAudio(), called much more often, where it interpolates between the control values.
This also allows the MultiLine updates to be made even more sparsely if desired, eg. every 3rd control update.
@tparam CONTROL_UPDATE_RATE The frequency of control updates.  
Ordinarily this will be CONTROL_RATE, but an alternative (amongst others) is
to set this as well as the LERP_RATE parameter to AUDIO_RATE, and call both update() and next() in updateAudio().
Such a use would allow accurate envelopes with finer resolution of the control points than CONTROL_RATE.
@tparam LERP_RATE Sets how often next() will be called, to interpolate between updates set by CONTROL_UPDATE_RATE.
This will produce the smoothest results if it's set to AUDIO_RATE, but if you need to save processor time and your
envelope changes slowly or controls something like a filter where there may not be problems with glitchy or clicking transitions,
LERP_RATE could be set to CONTROL_RATE (for instance).  Then update() and next() could both be called in updateControl(), 
greatly reducing the amount of processing required compared to calling next() in updateAudio().
@todo Test whether using the template parameters makes any difference to speed, 
and rationalise which units which do and don't need them.  
Template objects are messy when you try to use pointers to them, 
you have to include the whole template shebang in the pointer handling.
*/
template <unsigned int CONTROL_UPDATE_RATE, unsigned int LERP_RATE>
class MultiLine
{
private:

	const unsigned int LERPS_PER_CONTROL;

	unsigned int update_step_counter;
	unsigned int num_update_steps;

	enum {LINE1,LINE2,LINE3,LINE4,IDLE};


	struct phase{
		byte phase_type;
		unsigned int update_steps;
		long lerp_steps; // signed, to match params to transition (line) type Q15n16, below
		Q15n16 level;
	}target1,target2,target3,target4,idle;

	phase * current_phase;
	Line <Q15n16> transition; 
	
	inline
	unsigned int convertMsecToControlUpdateSteps(unsigned int msec){
		return (uint16_t) (((uint32_t)msec*CONTROL_UPDATE_RATE)>>10); // approximate /1000 with shift
	}


	inline
	void setPhase(phase * next_phase) {
		update_step_counter = 0;
		num_update_steps = next_phase->update_steps;
		transition.set(next_phase->level, next_phase->lerp_steps);
		current_phase = next_phase;
	}



	inline
	void checkForAndSetNextPhase(phase * next_phase) {
		if (++update_step_counter >= num_update_steps){
			setPhase(next_phase);
		}
	}



	inline
	void setTime(phase * p, unsigned int msec)
	{
		p->update_steps = convertMsecToControlUpdateSteps(msec);
		p->lerp_steps = (long) p->update_steps * LERPS_PER_CONTROL;
	}


	inline
	void setUpdateSteps(phase * p, unsigned int steps)
	{
		p->update_steps = steps;
		p->lerp_steps = (long) steps * LERPS_PER_CONTROL;
	}



public:

	/** Constructor.
	 */
	MultiLine():LERPS_PER_CONTROL(LERP_RATE/CONTROL_UPDATE_RATE)
	{
		target1.phase_type = LINE1;
		target2.phase_type = LINE2;
		target3.phase_type = LINE3;
		target4.phase_type = LINE4;
		idle.phase_type = IDLE;
		target4.level = 0;
		current_phase = &idle;
	}



	/** Updates the internal controls of the MultiLine.
		Call this in updateControl().
		*/
	void update(){ // control rate

		switch(current_phase->phase_type) {

		case LINE1:
			checkForAndSetNextPhase(&target2);
			break;

		case LINE2:
			checkForAndSetNextPhase(&target3);
			break;

		case LINE3:
			checkForAndSetNextPhase(&target4);
			break;

		case LINE4:
			checkForAndSetNextPhase(&idle);
			//checkForAndSetIdle();
			break;

		case IDLE:
			break;
		}
	}



	/** Advances one step along the MultiLine and returns the level.
	Call this in updateAudio().
	@return the next value, as a Q15n16 fixed-point number.
	 */
	inline
	Q15n16 next() 
	{
		return transition.next();
	}



	/** Start the target1 phase of the MultiLine.  THis will restart the MultiLine no matter what phase it is up to.
	*/
	inline
	void start(){
		setPhase(&target1);
	}



	/** Start the target4 phase of the MultiLine.
	@todo fix target4 for rate rather than steps (time), so it "releases" at the same rate whatever the current level.
	*/
	inline
	void stop(){
		setPhase(&target4);
	}



	/** Set the target1 level of the MultiLine.
	@param value the target1 level.
	 */
	inline
	void setTarget1Level(Q15n16 value)
	{
		target1.level=value;
	}



	/** Set the target2 level of the MultiLine.
	@param value the target2 level.
	*/
	inline
	void setTarget2Level(Q15n16 value)
	{
		target2.level=value;
	}


	/** Set the target3 level of the MultiLine.
	@param value the target3 level.  Usually the same as the target2 level, 
	for a steady target3ed note.
	*/
	inline
	void setTarget3Level(Q15n16 value)
	{
		target3.level=value;
	}

	/** Set the target4 level of the MultiLine.  Normally you'd make this 0,
	but you have the option of some other value.
	@param value the target4 level (usually 0).
	*/
	inline
	void setTarget4Level(Q15n16 value)
	{
		target4.level=value;
	}


		inline
	void setIdleLevel(Q15n16 value)
	{
		idle.level=value;
	}


	/** Set the target1, target2, target3 and target4 levels.
	@param target1 the new target1 level.
	@param target2 the new target3 level.
	@param target1 the new target3 level.
	@param target2 the new target4 level.
	*/
	inline
	void setLevels(Q15n16 target1, Q15n16 target2, Q15n16 target3, Q15n16 target4)
	{
		setTarget1Level(target1);
		setTarget2Level(target2);
		setTarget3Level(target3);
		setTarget4Level(target4);
		setIdleLevel(0);	
	}


	/** Set the target1 time of the MultiLine in milliseconds.
	The actual time taken will be resolved within the resolution of CONTROL_RATE.
	@param msec the unsigned int target1 time in milliseconds.
	@note Beware of low values (less than 20 or so, depending on how many steps are being taken),
	in case internal step size gets calculated as 0, which would mean nothing happens.
	 */
	inline
	void setTarget1Time(unsigned int msec)
	{
		setTime(&target1, msec);
	}


	/** Set the target2 time of the MultiLine in milliseconds.
	The actual time taken will be resolved within the resolution of CONTROL_RATE.
	@param msec the unsigned int target2 time in milliseconds.
	@note Beware of low values (less than 20 or so, depending on how many steps are being taken),
	in case internal step size gets calculated as 0, which would mean nothing happens.
	*/
	inline
	void setTarget2Time(unsigned int msec)
	{
		setTime(&target2, msec);
	}


	/** Set the target3 time of the MultiLine in milliseconds.
	The actual time taken will be resolved within the resolution of CONTROL_RATE.
	The target3 phase will finish if the MultiLine recieves a stop().
	@param msec the unsigned int target3 time in milliseconds.
	@note Beware of low values (less than 20 or so, depending on how many steps are being taken),
	in case internal step size gets calculated as 0, which would mean nothing happens.
	*/
	inline
	void setTarget3Time(unsigned int msec)
	{
		setTime(&target3, msec);
	}



	/** Set the target4 time of the MultiLine in milliseconds.
	The actual time taken will be resolved within the resolution of CONTROL_RATE.
	@param msec the unsigned int target4 time in milliseconds.
	@note Beware of low values (less than 20 or so, depending on how many steps are being taken),
	in case internal step size gets calculated as 0, which would mean nothing happens.
	*/
	inline
	void setTarget4Time(unsigned int msec)
	{
		setTime(&target4, msec);
	}


	inline
	void setIdleTime(unsigned int msec)
	{
		setTime(&idle, msec); 	
	}
	

	/** Set the target1, target2 and target4 times of the MultiLine in milliseconds.
	The actual times will be resolved within the resolution of CONTROL_RATE.
	@param target1_ms the new target1 time in milliseconds.
	@param target2_ms the new target2 time in milliseconds.
	@param target3_ms the new target3 time in milliseconds.
	@param target4_ms the new target4 time in milliseconds.
	@note Beware of low values (less than 20 or so, depending on how many steps are being taken),
	in case internal step size gets calculated as 0, which would mean nothing happens.
	*/
	inline
	void setTimes(unsigned int target1_ms, unsigned int target2_ms, unsigned int target3_ms, unsigned int target4_ms)
	{
		setTarget1Time(target1_ms);
		setTarget2Time(target2_ms);
		setTarget3Time(target3_ms);
		setTarget4Time(target4_ms);
		setIdleTime(65535); // guarantee step size of line will be 0
	}



	/** Set the target1 time of the MultiLine, expressed as the number of update steps (not MultiLine::next() interpolation steps) in the target1 phase.
	@param steps the number of times MultiLine::update() will be called in the target1 phase.
	 */
	inline
	void setTarget1UpdateSteps(unsigned int steps)
	{
		setUpdateSteps(&target1, steps);
	}


	/** Set the target2 time of the MultiLine, expressed as the number of update steps (not MultiLine::next() interpolation steps) in the target2 phase.
	@param steps the number of times MultiLine::update() will be called in the target2 phase.
	 */
	inline
	void setTarget2UpdateSteps(unsigned int steps)
	{
		setUpdateSteps(&target2, steps);
	}


	/** Set the target3 time of the MultiLine, expressed as the number of update steps (not MultiLine::next() interpolation steps) in the target3 phase.
	@param steps the number of times MultiLine::update() will be called in the target3 phase.
	*/
	inline
	void setTarget3UpdateSteps(unsigned int steps)
	{
		setUpdateSteps(&target3, steps);
	}


	/** Set the target4 time of the MultiLine, expressed as the number of update steps (not MultiLine::next() interpolation steps) in the target4 phase.
	@param steps the number of times MultiLine::update() will be called in the target4 phase.
	 */
	inline
	void setTarget4UpdateSteps(unsigned int steps)
	{
		setUpdateSteps(&target4, steps);
	}


		inline
	void setIdleUpdateSteps(unsigned int steps)
	{
		setUpdateSteps(&idle, steps);
	}
	
	/** Set the target1, target2 and target4 times of the MultiLine, expressed in update steps (not MultiLine::next() interpolation steps).
	@param target1_steps the number of update steps in the target1 phase
	@param target2_steps the number of update steps in the target2 phase
	@param target3_steps the number of update steps in the target3 phase
	@param target4_steps the number of update steps in the target4 phase
	*/
	inline
	void setAllUpdateSteps(unsigned int target1_steps, unsigned int target2_steps, unsigned int target3_steps, unsigned int target4_steps)
	{
		setTarget1UpdateSteps(target1_steps);
		setTarget2UpdateSteps(target2_steps);
		setTarget3UpdateSteps(target3_steps);
		setTarget4UpdateSteps(target4_steps);
		setIdleUpdateSteps(65535); // guarantee? step size of line will be 0?
	}



	/** Tells if the envelope is currently playing.
	@return true if playing, false if in IDLE state
	*/
	inline
	bool playing()
	{
		return !(current_phase->phase_type==IDLE);
	}


};


/** @example 07.Envelopes/MultiLine_Envelope/MultiLine_Envelope.ino
This is an example of how to use the MultiLine class.
*/

#endif /* MultiLine_H_ */