Zigbee2MQTT Post Install | USB-Adapter #410

MickLesk · 2024-11-21T07:13:57Z

MickLesk
Nov 21, 2024
Maintainer

Copied from original post: tteck/Proxmox#2917

Zigbee2MQTT Setup Guide

This guide will help you set up Zigbee2MQTT on your system. Follow the steps carefully to ensure a smooth installation and configuration process.

⚙️ Determine the Location of Your Adapter

Run the following command to find the location of your Zigbee adapter:

ls -l /dev/serial/by-id

Example Output:

lrwxrwxrwx 1 root root 13 Jun 19 17:30 usb-1a86_USB_Serial-if00-port0 -> ../../ttyUSB0

⚠️Make a note of the value after -> (e.g., /dev/ttyUSB0 or /dev/serial/by-id/usb-...), as you will need it in the configuration file.

⚙️ Edit the Configuration File

Before starting Zigbee2MQTT, edit the configuration.yaml file.

📃For Debian:

nano /opt/zigbee2mqtt/data/configuration.yaml

📃For Alpine:

nano /root/.z2m/configuration.yaml

Save and exit the editor using: Ctrl+O, then Enter, and Ctrl+X.

🔏 Example Configuration:

frontend:
  port: 9442
homeassistant: true
permit_join: false
mqtt:
  base_topic: zigbee2mqtt
  server: 'mqtt://192.168.86.224:1883'
  user: usr
  password: pwd
  keepalive: 60
  reject_unauthorized: true
  version: 4
serial:
  # Location of the adapter
  # USB adapters - use format "port: /dev/serial/by-id/XXX"
  # Ethernet adapters - use format "port: tcp://192.168.1.12:6638"
  port: /dev/serial/by-id/usb-Texas_Instruments_TI_CC2531_USB_CDC___0X00124B0018ED3DDF-if00
  # Adapter type, allowed values: `zstack`, `ember`, `deconz`, `zigate` or `zboss`
  adapter: zstack
advanced:
  pan_id: GENERATE
  network_key: GENERATE
  channel: 20

Make sure to update the serial section with your adapter's location and uncomment the appropriate adapter type if necessary.

⚙️ Start Zigbee2MQTT

After completing the configuration, you can start Zigbee2MQTT.

📃For Debian:

systemctl restart zigbee2mqtt

📃For Alpine:

rc-update add zigbee2mqtt default

JesperKuipers · 2024-11-24T22:14:38Z

JesperKuipers
Nov 24, 2024

2 replies

JesperKuipers Nov 27, 2024

dev branch seems to work tho

D3rPaPaH0d3n Feb 6, 2025

How did you change to dev branch? I tried already so many things, but i don´t get it!

LeonGrim2024 · 2024-11-27T07:38:10Z

LeonGrim2024
Nov 27, 2024

I have not any errors, but can't connect

to web-interface after install. and console look odd. reboot not fix. HELP...

1 reply

dsiebel Dec 3, 2024

Did you enable the frontend in your config?
https://www.zigbee2mqtt.io/guide/configuration/frontend.html

If the frontend was enabled, the log should show a line like:

info: z2m: Started frontend on port 0.0.0.0:8080

hadros01 · 2024-12-02T22:49:30Z

hadros01
Dec 2, 2024

Hello,
I'm a little bit lost. I followed (hopefully complete) the documentation to install zigbee2mqtt on a raspberry 3b. I use the sonoff zigbee 3.0 USB dongle plus.While the installation I didn't saw any error. Now, if I start it, I get the following log and after that the raspi stuck and is dead. Not reachable anymore. Following the log infos.

[email protected] start
node index.js

Starting Zigbee2MQTT without watchdog.
[2024-12-02 22:31:32] info: z2m: Logging to console, file (filename: log.log)
[2024-12-02 22:31:32] debug: z2m: Can't load state from file /opt/zigbee2mqtt/data/state.json (doesn't exist)
[2024-12-02 22:31:32] info: z2m: Starting Zigbee2MQTT version 1.42.0 (commit #861cba6)
[2024-12-02 22:31:32] debug: z2m: sd-notify loaded
[2024-12-02 22:31:32] info: z2m: Starting zigbee-herdsman (2.1.9)
[2024-12-02 22:31:32] debug: z2m: Using zigbee-herdsman with settings: '"{"network":{"panID":6754,"extendedPanID":[221,221,221,221,221,221,221,221],"channelList":[11],"networkKey":"HIDDEN"},"databasePath":"/opt/zigbee2mqtt/data/database.db","databaseBackupPath":"/opt/zigbee2mqtt/data/database.db.backup","backupPath":"/opt/zigbee2mqtt/data/coordinator_backup.json","serialPort":{"path":"/dev/serial/by-id/usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20230329145849-if00","adapter":"ember"},"adapter":{"disableLED":false}}"'
[2024-12-02 22:31:33] debug: zh:adapter: Path '/dev/serial/by-id/usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20230329145849-if00' is valid for 'EmberAdapter'
[2024-12-02 22:31:33] info: zh:ember: Using default stack config.
[2024-12-02 22:31:33] debug: zh:controller: Starting with options '{"network":{"networkKeyDistribute":false,"networkKey":"HIDDEN","panID":6754,"extendedPanID":[221,221,221,221,221,221,221,221],"channelList":[11]},"serialPort":{"path":"/dev/serial/by-id/usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20230329145849-if00","adapter":"ember"},"adapter":{"disableLED":false},"databasePath":"/opt/zigbee2mqtt/data/database.db","databaseBackupPath":"/opt/zigbee2mqtt/data/database.db.backup","backupPath":"/opt/zigbee2mqtt/data/coordinator_backup.json"}'
[2024-12-02 22:31:33] info: zh:ember: ======== Ember Adapter Starting ========
[2024-12-02 22:31:33] info: zh:ember:ezsp: ======== EZSP starting ========
[2024-12-02 22:31:33] info: zh:ember:uart:ash: ======== ASH Adapter reset ========
[2024-12-02 22:31:33] info: zh:ember:uart:ash: RTS/CTS config is off, enabling software flow control.
[2024-12-02 22:31:33] debug: zh:ember:uart:ash: Opening serial port with {"path":"/dev/serial/by-id/usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20230329145849-if00","baudRate":115200,"rtscts":false,"autoOpen":false,"parity":"none","stopBits":1,"xon":true,"xoff":true}

1 reply

dsiebel Dec 3, 2024

You mention installing on a Raspberry Pi, how is this related to Proxmox LXC and this script?

hadros01 · 2024-12-03T11:57:36Z

hadros01
Dec 3, 2024

Yes, I made the installation related to the description for Linux Raspian. From Proxmox LXC I know nothing. Why do you ask about Proxmox?

1 reply

dsiebel Dec 9, 2024

Because you're posting in a repository that provides script to provision Proxmox LXCs and VMs.
This repository has nothing to do with Raspbian OR Raspberry Pi.

hadros01 · 2024-12-09T08:31:23Z

hadros01
Dec 9, 2024

Oh sorry. I'm new here in Git and it is a little bit unclear to me.
But nevertheless I have solved my problem.

0 replies

Kuchiru · 2024-12-14T15:07:54Z

Kuchiru
Dec 14, 2024

Hello there,

How do i update/upgrade Z2M on the Alpine version of this LXC?

3 replies

Kuchiru Dec 15, 2024

Appears it is installed as a package apk update && apk upgrade will do it.

JensjJ8200 Jan 21, 2025

how do you update the non Alpine version?

Kuchiru Feb 3, 2025

how do you update the non Alpine version?

rerun the install script inside the vm/lxc, it'll give you an upgrade option.

dsiebel · 2024-12-16T13:03:45Z

dsiebel Dec 16, 2024

Looks like the MQTT server can not be connected.
Have you tried connecting to mqtt://192.168.1.250:1883 with e.g. MQTT Explorer? Did it work?
Have you tried removing the mqtt://? Shouldn't be needed since it's implied.

MickLesk · 2024-12-16T14:02:54Z

MickLesk Dec 16, 2024
Maintainer Author

Koenkk/zigbee2mqtt#16207

thats not an support discussion!

dsiebel · 2024-12-16T16:47:43Z

dsiebel Dec 16, 2024

yeah, so the config is fine. Looks like you need to update your version of zigbee2mqtt.

MickLesk · 2025-01-04T08:26:28Z

MickLesk Jan 4, 2025
Maintainer Author

this is not a discussion!

sylarm27 · 2025-01-07T16:49:19Z

sylarm27
Jan 7, 2025

Hello,

I'm trying to update zigbee2mqtt debian to version 2.0.0 but I got error, and also if I try to build new container I got error:

Please, What is you procedure for update?

Regards

3 replies

MickLesk Jan 7, 2025
Maintainer Author

Definitly wrong script and read changelog With breaking Change & this is not n Issue topic

sylarm27 Jan 7, 2025

Thank you.
What changlog you refer? I will read it for sure. Because this is stuck, and the only way I see is moving to ZHA. But I prefer this current method.

MickLesk Jan 7, 2025
Maintainer Author

Our Changelog. & U use the tteck repo

Beel12213 · 2025-01-16T11:01:17Z

Beel12213
Jan 16, 2025

Hey, I'm having real trouble getting this to work for some reason and I'm not sure where I'm going wrong. I've used the Proxmox Helper Script to setup and install the LXC. Noticed the USB device is automatically setup/passed through, so I've then gone ahead and edited the config as suggested in your guide here.

However, for the life of me, I can't figure out why the frontend is not booting up.

When I looked at the logs I got the below error, is anyone able to help me figure out where I'm going wrong please?

Jan 16 10:58:24 zigbee2mqtt systemd[1]: Started zigbee2mqtt.service - zigbee2mqtt.
Jan 16 10:58:24 zigbee2mqtt pnpm[2361]: > [email protected] start /opt/zigbee2mqtt
Jan 16 10:58:24 zigbee2mqtt pnpm[2361]: > node index.js
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: Starting Zigbee2MQTT without watchdog.
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         z2m: Logging to console, file (filename: log.log)
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         z2m: Starting Zigbee2MQTT version 2.0.0 (commit #unknown)
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         z2m: Starting zigbee-herdsman (3.2.1)
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember: Using default stack config.
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember: ======== Ember Adapter Starting ========
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember:ezsp: ======== EZSP starting ========
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember:uart:ash: ======== ASH Adapter reset ========
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember:uart:ash: RTS/CTS config is off, enabling software flow control.
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember:uart:ash: Serial port opened
Jan 16 10:58:25 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:25] info:         zh:ember:uart:ash: ======== ASH starting ========
Jan 16 10:58:28 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:28] info:         zh:ember:uart:ash: ======== ASH Adapter reset ========
Jan 16 10:58:28 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:28] info:         zh:ember:uart:ash: ======== ASH starting ========
Jan 16 10:58:30 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:30] info:         zh:ember:uart:ash: ======== ASH Adapter reset ========
Jan 16 10:58:30 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:30] info:         zh:ember:uart:ash: ======== ASH starting ========
Jan 16 10:58:33 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:33] info:         zh:ember:uart:ash: ======== ASH Adapter reset ========
Jan 16 10:58:33 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:33] info:         zh:ember:uart:ash: ======== ASH starting ========
Jan 16 10:58:35 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:35] info:         zh:ember:uart:ash: ======== ASH Adapter reset ========
Jan 16 10:58:35 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:35] info:         zh:ember:uart:ash: ======== ASH starting ========
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:38] error:         z2m: Error while starting zigbee-herdsman
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:38] error:         z2m: Failed to start zigbee-herdsman
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:38] error:         z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start_crashes-runtime.html for possible solutions
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:38] error:         z2m: Exiting...
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]: [2025-01-16 10:58:38] error:         z2m: Error: Failed to start EZSP layer with status=HOST_FATAL_ERROR.
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at EmberAdapter.initEzsp (/opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/zigbee-herdsman/src/adapter/ember/adapter/emberAdapter.ts:670:19)
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at EmberAdapter.start (/opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/zigbee-herdsman/src/adapter/ember/adapter/emberAdapter.ts:1533:24)
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at Controller.start (/opt/zigbee2mqtt/node_modules/.pnpm/[email protected]/node_modules/zigbee-herdsman/src/controller/controller.ts:136:29)
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at Zigbee.start (/opt/zigbee2mqtt/lib/zigbee.ts:69:27)
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at Controller.start (/opt/zigbee2mqtt/lib/controller.ts:142:13)
Jan 16 10:58:38 zigbee2mqtt pnpm[2373]:     at start (/opt/zigbee2mqtt/index.js:161:5)
Jan 16 10:58:38 zigbee2mqtt pnpm[2361]:  ELIFECYCLE  Command failed with exit code 1.
Jan 16 10:58:38 zigbee2mqtt systemd[1]: zigbee2mqtt.service: Main process exited, code=exited, status=1/FAILURE
Jan 16 10:58:38 zigbee2mqtt systemd[1]: zigbee2mqtt.service: Failed with result 'exit-code'.
Jan 16 10:58:38 zigbee2mqtt systemd[1]: zigbee2mqtt.service: Consumed 1.753s CPU time.
Jan 16 10:58:38 zigbee2mqtt systemd[1]: zigbee2mqtt.service: Scheduled restart job, restart counter is at 37.
Jan 16 10:58:38 zigbee2mqtt systemd[1]: Stopped zigbee2mqtt.service - zigbee2mqtt.
Jan 16 10:58:38 zigbee2mqtt systemd[1]: zigbee2mqtt.service: Consumed 1.753s CPU time.

My config file is below - I'm using the device "SONOFF Universal Zigbee 3.0 USB Dongle Plus Gateway with Antenna for Home Assistant, IoBroker, Zigbee2MQTT":

frontend:
  enabled: true
  port: 9442
homeassistant:
  enabled: true
mqtt:
  base_topic: zigbee2mqtt
  server: mqtt://192.168.1.36:1883
  user: usr
  password: pwd
  keepalive: 60
  reject_unauthorized: true
  version: 4
serial:
  port: >-
    /dev/serial/by-id/usb-ITead_Sonoff_Zigbee_3.0_USB_Dongle_Plus_b071257761beed11b7dc9b4838a92db5-if00-port0
  adapter: ember
advanced:
  pan_id: 39150
  network_key:
    - 174
    - 44
    - 17
    - 18
    - 62
    - 66
    - 151
    - 66
    - 34
    - 219
    - 217
    - 171
    - 189
    - 15
    - 138
    - 217
  channel: 20
version: 4

3 replies

MickLesk Jan 16, 2025
Maintainer Author

Error: Failed to start EZSP layer with status=HOST_FATAL_ERROR.

check if your stick reachable or connected

by the way, you have an Sonoff, then its zstack?

sylarm27 Jan 16, 2025

The USB device is not in use by other service? or container? Reboot the proxmox it self.
I know if I stop one zigbee2mqtt LXC and try to create a new one I got that error. I need to stop the old LXC present it to start on boot and then reboot. Like that I can create a new one. Was my story....

Beel12213 Jan 16, 2025

Used both fixes suggested above and it seems to be working/booting up now. Really apprecaite both your help and QUICK feedback.

Steps to Fix (incase anyone else has this issue):

Delete the LXC
Reboot Proxmox
Create the LXC (Don't manually passthrough the USB, it's done automatically with the script!)
Make sure to select the right adapter type (ember/zstack/deconz/zigate/zboss)
Follow the instructions from the main post
(The MQTT section wants your broker's details not the zigbee2mqtt's IP. Don't be dumb x 2 like me)

JensjJ8200 · 2025-01-16T20:55:12Z

JensjJ8200
Jan 16, 2025

2 replies

MickLesk Jan 16, 2025
Maintainer Author

Ember is wrong for sonoff? Zstack should be right. My 2 old sonoffs where anytime zstack? Or is this a special flashed ?

I think the Z2M Repo where better to ask

MickLesk Jan 16, 2025
Maintainer Author

I only see, that the adapter crashed at start, but idk, ive now an Network device (POE) for this

tugsi · 2025-01-22T10:42:39Z

tugsi
Jan 22, 2025

@MickLesk Please edit the Configuration Example under the Point Serial is the type of Adapter to be declared

serial:
    # Location of the adapter
    # USB adapters - use format "port: /dev/serial/by-id/XXX"
    # Ethernet adapters - use format "port: tcp://192.168.1.12:6638"
    port: /dev/serial/by-id/usb-Texas_Instruments_TI_CC2531_USB_CDC___0X00124B0018ED3DDF-if00
    # Adapter type, allowed values: `zstack`, `ember`, `deconz`, `zigate` or `zboss`
    adapter: zstack

Found on https://github.com/Koenkk/zigbee2mqtt.io/blob/dev/docs/guide/configuration/adapter-settings.md#basic-configuration

1 reply

MickLesk Jan 22, 2025
Maintainer Author

done

LeonGrim2024 · 2025-01-22T16:37:09Z

LeonGrim2024
Jan 22, 2025

how to update to Zigbee2MQTT V2 now ?

2 replies

MickLesk Jan 22, 2025
Maintainer Author

read changelog and guides not here!

tugsi Jan 23, 2025

how to update to Zigbee2MQTT V2 now ?

I know, normally not here, but a quick answer.
I have made a new LXC with the TTeck-Script, for the new V2. Then I have copied the data-directory from the old LXC (opt/zigbee2mqtt/data) to the new LXC and replaced there the folder with the copied one. After that, I shutdown the old one, gave the new LXC the same IP (only for me, to have the same IP) and restarted, after that all done and works ;-)

kopaszsop · 2025-01-29T11:28:45Z

kopaszsop
Jan 29, 2025

hi,
is there a way to install the 1.42.0 version of z2m with this script? i've problems with some ikea hardware wich worked for me but with the 2.0.0 version they don't.

7 replies

tugsi Jan 29, 2025

Which IKEA Hardware has problems? I have some too and no problems.

kopaszsop Jan 29, 2025

Which IKEA Hardware has problems? I have some too and no problems.

thx.
it's the E1743 on/off button.
z2m doesn't gives any switchable/controllable einties over to homeassistant

tugsi Jan 30, 2025

Ok I´ve seen. I use ioBroker, there is everything fine, over MQTT you get the zigbee2mqtt/E1743/action too, where you have false/true for on/off .
But I have a test enviroment from HA and there I can see, is only battery, lastseen, linkquality, update .
It seems there is something changed in Z2M, maybe better post an issue there. For the meanwhile you can go over an MQTT-Broker if you want to use 2.0+

kopaszsop Jan 30, 2025

Ok I´ve seen. I use ioBroker, there is everything fine, over MQTT you get the zigbee2mqtt/E1743/action too, where you have false/true for on/off . But I have a test enviroment from HA and there I can see, is only battery, lastseen, linkquality, update . It seems there is something changed in Z2M, maybe better post an issue there. For the meanwhile you can go over an MQTT-Broker if you want to use 2.0+

i've found this and tried all the checkboxes under the hood but i only get on-off-up-down-release states as "event" in HA.
Koenkk/zigbee2mqtt#25502 (comment)

so this problem affects the z2m and not this script.

tugsi Jan 30, 2025

I´ve seen your post and have checked in my installation the legacy action box and now I have the Action Entities in HA

Alyosha777 · 2025-02-04T10:00:55Z

Alyosha777
Feb 4, 2025

I have just completed this setup and frontend is working for me and I have the configuration.yaml set up. My need is to migrate from Zigbee2mqtt running in HA. I have mosquito running in HA still.
I'm having difficulty importing my backup. The backup from HA has configuration.yaml, database.db, coordinator_backup.json, and state.json. Editing these folders on the Proxmox container does not lead to my devices showing up in my new Zigbee2mqtt. Anyone have success importing devices? I'd prefer to avoid repairing all devices.

0 replies

cyberdie · 2025-02-07T10:07:15Z

cyberdie
Feb 7, 2025

Hi. The z2m lxc is not showing the usb adapter in /dev/serial/by-id path but lsusb shows the adapter correctly.
How can i configure z2m with this information? ttyUSB0/1, ttyACM0/1 didn't work :-(

5 replies

MickLesk Feb 7, 2025
Maintainer Author

execute this on main node

cyberdie Feb 7, 2025

No /dev/serial path on main node....

MickLesk Feb 7, 2025
Maintainer Author

then you dont have an connected COM Device on your port. Or Your device is broken

cyberdie Feb 7, 2025

The device is shown in lsusb (Texas Instruments CC2531....)

MickLesk Feb 7, 2025
Maintainer Author

and the COM Port is not reachable. look this or ask in zigbee2mqtt discussions
https://forum.iobroker.net/topic/29761/gel%C3%B6st-cc2531-an-proxmox-an-lxc-durchreichen-scheitert/61?lang=en-GB

MattSpeke · 2025-02-19T16:12:47Z

MattSpeke
Feb 19, 2025

Trying to update Z2M from v1 using ttekk script to v2 using the new script. I get the error below. How do I upgrade/migrate from the old version to the new verson?

1 reply

MickLesk Feb 19, 2025
Maintainer Author

Use search function, read our Changelog and you found it

This comment has been hidden.

Sign in to view

Zigbee2MQTT Post Install | USB-Adapter #410

MickLesk Nov 21, 2024 Maintainer

Zigbee2MQTT Setup Guide

⚙️ Determine the Location of Your Adapter

⚙️ Edit the Configuration File

🔏 Example Configuration:

⚙️ Start Zigbee2MQTT

Replies: 19 comments · 36 replies

This comment has been hidden.

This comment was marked as disruptive content.

This comment was marked as disruptive content.

MickLesk Dec 16, 2024 Maintainer Author

This comment was marked as off-topic.

MickLesk Jan 4, 2025 Maintainer Author

MickLesk Jan 7, 2025 Maintainer Author

MickLesk Jan 7, 2025 Maintainer Author

MickLesk Jan 16, 2025 Maintainer Author

MickLesk Jan 16, 2025 Maintainer Author

MickLesk Jan 16, 2025 Maintainer Author

MickLesk Jan 22, 2025 Maintainer Author

MickLesk Jan 22, 2025 Maintainer Author

MickLesk Feb 7, 2025 Maintainer Author

MickLesk Feb 7, 2025 Maintainer Author

MickLesk Feb 7, 2025 Maintainer Author

MickLesk Feb 19, 2025 Maintainer Author

MickLesk
Nov 21, 2024
Maintainer

Replies: 19 comments 36 replies

MickLesk Dec 16, 2024
Maintainer Author

MickLesk Jan 4, 2025
Maintainer Author

MickLesk Jan 7, 2025
Maintainer Author

MickLesk Jan 7, 2025
Maintainer Author

MickLesk Jan 16, 2025
Maintainer Author

MickLesk Jan 16, 2025
Maintainer Author

MickLesk Jan 16, 2025
Maintainer Author

MickLesk Jan 22, 2025
Maintainer Author

MickLesk Jan 22, 2025
Maintainer Author

MickLesk Feb 7, 2025
Maintainer Author

MickLesk Feb 7, 2025
Maintainer Author

MickLesk Feb 7, 2025
Maintainer Author

MickLesk Feb 19, 2025
Maintainer Author