analogmux

\mainpage Main Page

---

Analog MUX click

Analog MUX Click is a Click board™ that switches one of the sixteen inputs to one output. It employs the CD74HC4067, a High-Speed CMOS Logic 16-Channel Analog Multiplexer/Demultiplexer, produced by Texas Instruments.

click Product page

---

Click library

• Author : MikroE Team
• Date : Jun 2020.
• Type : ADC type

Software Support

We provide a library for the AnalogMUX Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for AnalogMUX Click driver.

Standard key functions :

• Config Object Initialization function.

void analogmux_cfg_setup ( analogmux_cfg_t *cfg );

• Initialization function.

ANALOGMUX_RETVAL analogmux_init ( analogmux_t *ctx, analogmux_cfg_t *cfg );

Example key functions :

• Generic read voltage function.

float analogmux_get_voltage ( float adc_val, uint16_t vref, uint16_t rez );

• This function sets the active channel on the MUX.

void analogmux_set_channel ( analogmux_t *ctx, uint8_t cfg );

Examples Description

This example showcases how to initialize, configure and use the Analog MUX click module. The click switches one of the 16 inputs to output so the adc value of that input can be read on the COM (AN) pin. The RST, PWM, CS and INT are used as control output pins.

The demo application is composed of two sections :

Application Init

This function initializes and configures the logger and click modules.

void application_init ( void )
{
    log_cfg_t log_cfg;
    analogmux_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    Delay_100ms( );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    analogmux_cfg_setup( &cfg );
    ANALOGMUX_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    analogmux_init( &analogmux, &cfg );

    analogmux_set_channel( &analogmux, ANALOGMUX_CHANNEL_0 );
    log_printf( &logger, " Channel 0 enabled\r\n" );
    log_printf( &logger, " -------------------\r\n" );
}
  

Application Task

This function reads ADC value and voltage from channel 0 (AN0) and shows the results on the USB UART every 2 seconds.

void application_task ( void )
{
    uint16_t tmp;
    float val;

    tmp = analogmux_generic_read( &analogmux );
    
    log_printf( &logger, " ADC value : %u\r\n", tmp );

    val = analogmux_generic_read_voltage( &analogmux );

    log_printf( &logger, " Voltage: %.3f mV\r\n", val );
    log_printf( &logger, " -------------------\r\n" );

    Delay_ms( 2000 );
}

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.AnalogMUX

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---