make arduino328p fails if i2c is enabled in config file

[MOOSFETT]

hi,

if i enable the i2c-option(s) in the arduino328p.conf.mk i'm getting an odd output on the make command. i've no clue what went wrong... when setting back e.g. to UART bus, everything goes fine.

unfortunately, i'm very new to the raspi and all the linux stuff, so i would really appreciate any hints and support also in terms of posting issues here.

i hope it is okay to post all the stuff in this form of presentation...
first, the enabled lines of the conf.mk, after that i've pasted the mentioned output of the make-command.

resulting switches in the conf.mk:

USE_CONFIG_H = yes
MCU = atmega328p
BOOTSZ=0
F_CPU = 16000000
USE_DFLL = yes
OVERRIDE_AVRDUDE_PROGRAMMER = yes
AVRDUDE_PROGRAMMER = avrispmkII
AVRDUDE_PORT = usb
AVRDUDE_FUSES =
USE_ENTER_DELAY = yes
USE_ENTER_PIN = no
USE_ENTER_UART = no
USE_ENTER_I2C = yes
USE_ENTER_FIFO = no
USE_ENTER_EEPROM = no
LOCK_SPM_ON_EXIT = no
USE_LED = yes
USE_UART = no
USE_UART_EN_PIN = no
USE_I2C = yes
USE_I2C_ADDRESS_NEGOTIATION = no
USE_ATTACH_LED = no
USE_FIFO = no
USE_INTERRUPTS = no
USE_WATCHDOG = no
ENABLE_BLOCK_SUPPORT = yes
ENABLE_FLASH_BYTE_SUPPORT = yes
ENABLE_EEPROM_BYTE_SUPPORT = yes
ENABLE_LOCK_BITS = yes
ENABLE_FUSE_BITS = yes
ENABLE_FLASH_ERASE_WRITE = yes
ENABLE_CRC_SUPPORT = yes
ENABLE_API = yes
USE_API_VERSION = 1
ENABLE_API_LOW_LEVEL_FLASH = yes
ENABLE_API_SPM_WRAPPER = yes
ENABLE_API_FIRMWARE_UPDATE = yes
ENABLE_CODE_PROTECTION = no
ENABLE_EEPROM_PROTECTION = no
ENABLE_BOOTLOADER_PROTECTION = no
ENTER_PORT_NAME = C
ENTER_PIN = 0
ENTER_PIN_STATE = 0
ENTER_PIN_PUEN = 1
ENTER_BLINK_COUNT = 3
ENTER_BLINK_WAIT = 300000
ENTER_EEPROM_ADDR = 0x3f8;
WATCHDOG_TIMEOUT = WDT_PER_1KCLK_gc
LED_PORT_NAME = B
LED_PIN = 5
LED_INV = 1
UART_BAUD_RATE = 115200
UART_NUMBER = 0
UART_U2X = yes
UART_RX_PUEN = yes
UART_REMAP = no
UART_EN_PORT_NAME = C
UART_EN_PIN = 4
UART_EN_PIN_INV = 0
FIFO_DATA_PORT_NAME = C
FIFO_CTL_PORT_NAME = D
FIFO_RXF_N = 3
FIFO_TXE_N = 2
FIFO_RD_N = 1
FIFO_WR_N = 0
FIFO_BIT_REVERSE = yes
I2C_DEVICE_PORT = C
I2C_MATCH_ANY = 1
I2C_ADDRESS = 0x10
I2C_GC_ENABLE = 1

the output of the make command at prompt:

avr-gcc (GCC) 4.8.1
Copyright (C) 2013 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

Generating config.h for atmega328p

Compiling: xboot.c
avr-gcc -c -mmcu=atmega328p -I. -gstabs -Os -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums -ffunction-sections -fdata-sections -fno-jump-tables -Wall -Wa,-adhlns=xboot.lst -Wstrict-prototypes -std=gnu99 -MD -MP -MF .dep/xboot.o.d -DF_CPU=16000000L -DBOOT_SECTION_SIZE=0x001000 -DUSE_CONFIG_H xboot.c -o xboot.o
In file included from xboot.c:34:0:
xboot.c: In function ‘main’:
xboot.h:366:46: error: ‘TWIC’ undeclared (first use in this function)
#define I2C_DEVICE token_paste2(TWI, I2C_DEVICE_PORT)
^
xboot.h:43:32: note: in definition of macro ‘token_paste2_int’
#define token_paste2_int(x, y) x ## y
^
xboot.h:366:33: note: in expansion of macro ‘token_paste2’
#define I2C_DEVICE token_paste2(TWI, I2C_DEVICE_PORT)
^
i2c.h:45:31: note: in expansion of macro ‘I2C_DEVICE’
#define i2c_address_match() ((I2C_DEVICE.SLAVE.STATUS & TWI_SLAVE_APIF_bm) &&
^
xboot.c:388:21: note: in expansion of macro ‘i2c_address_match’
if (i2c_address_match())
^
xboot.h:366:46: note: each undeclared identifier is reported only once for each function it appears in
#define I2C_DEVICE token_paste2(TWI, I2C_DEVICE_PORT)
^
xboot.h:43:32: note: in definition of macro ‘token_paste2_int’
#define token_paste2_int(x, y) x ## y
^
xboot.h:366:33: note: in expansion of macro ‘token_paste2’
#define I2C_DEVICE token_paste2(TWI, I2C_DEVICE_PORT)
^
i2c.h:45:31: note: in expansion of macro ‘I2C_DEVICE’
#define i2c_address_match() ((I2C_DEVICE.SLAVE.STATUS & TWI_SLAVE_APIF_bm) &&
^
xboot.c:388:21: note: in expansion of macro ‘i2c_address_match’
if (i2c_address_match())
^
In file included from xboot.h:432:0,
from xboot.c:34:
i2c.h:45:57: error: ‘TWI_SLAVE_APIF_bm’ undeclared (first use in this function)
#define i2c_address_match() ((I2C_DEVICE.SLAVE.STATUS & TWI_SLAVE_APIF_bm) &&
^
xboot.c:388:21: note: in expansion of macro ‘i2c_address_match’
if (i2c_address_match())
^
i2c.h:46:36: error: ‘TWI_SLAVE_AP_bm’ undeclared (first use in this function)
(I2C_DEVICE.SLAVE.STATUS & TWI_SLAVE_AP_bm))
^
xboot.c:388:21: note: in expansion of macro ‘i2c_address_match’
if (i2c_address_match())
^
xboot.c: In function ‘get_char’:
xboot.c:1208:26: error: #error Not implemented!
#error Not implemented!
^
xboot.c: In function ‘send_char’:
xboot.c:1314:26: error: #error Not implemented!
#error Not implemented!
^
xboot.c:1233:23: warning: unused variable ‘tmp’ [-Wunused-variable]
unsigned char tmp;
^
Makefile:886: recipe for target 'xboot.o' failed
make[1]: *** [xboot.o] Error 1
make[1]: Leaving directory '/home/pi/xboot'
Makefile:779: recipe for target 'conf/arduino328p.conf.mk' failed
make: *** [conf/arduino328p.conf.mk] Error 2

thank you guys for checking this issue (if it is a real one ;o) !

regards,
richard