-
It seems like a roll of the dice anytime I start a new G7 sensor. I went through all the instructions on the github page, scanned the auto settings and went through the manual settings. I get asked to "Now start a new sensor" every time and it defaults to the 90 minute timer. Is this right or do I ignore it? If I'm lucky it eventually warms up in the 30 minutes. I just put a new one in, and about 25 minutes in I got a "Sensor Failed". Now at the 46 minute left mark I get a "Sensor Failed 7". I am leaving for a trip tomorrow and I'm stressing. I had one extra sensor and if I have to ditch this one I'm cutting it close. |
Beta Was this translation helpful? Give feedback.
Replies: 12 comments 23 replies
-
These are the instructions for using G7 as a collector: https://navid200.github.io/xDrip/docs/Dexcom/G7.html Can you post a screenshot of your G5/G6/G7/1 Status page? As an alternative, do you have a Dexcom G7 receiver? |
Beta Was this translation helpful? Give feedback.
-
I followed those instructions and triple checked them.
I may have to switch to the dexcom App but is it to late ?
…On Tue, May 14, 2024, 8:19 PM Navid ***@***.***> wrote:
These are the instructions for using G7 as a collector:
https://navid200.github.io/xDrip/docs/Dexcom/G7.html
Can you post a screenshot of your G5/G6/G7/1 Status page?
As an alternative, do you have a Dexcom G7 receiver?
Or, do you have a phone that is compatible with G7 Dexcom app?
—
Reply to this email directly, view it on GitHub
<#3463 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AGCVEWM5H7ECOYHBWQNVQL3ZCLH5ZAVCNFSM6AAAAABHXJQOISVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TINBQGQZDS>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
That screen is called the System Status so I was under the impression
that's what you were looking for. Do you want the Event Log?
…On Tue, May 14, 2024, 8:48 PM Navid ***@***.***> wrote:
Do what you need to. I asked you to show the status page. But, of course
you don't have to. But, why did you post here then?
—
Reply to this email directly, view it on GitHub
<#3463 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AGCVEWOPISIVC2S76I5VTMTZCLLKBAVCNFSM6AAAAABHXJQOISVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TINBQGU4DA>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
Auto-Connect disabled (for Samsung) |
Beta Was this translation helpful? Give feedback.
-
My phone updated this afternoon S906USQU4EXE1 |
Beta Was this translation helpful? Give feedback.
-
Bg level is 154 |
Beta Was this translation helpful? Give feedback.
-
Just a tiny bit, very slightly |
Beta Was this translation helpful? Give feedback.
-
After (and including) the 2024.08.07 xDrip release, sensor failed 7 condition will provide readings if readings are available. |
Beta Was this translation helpful? Give feedback.
-
@Navid200 thanks for the update. We upgraded from G6 to G7 today and ran into a "Sensor Failed 7" issue with a new G7 sensor. The sensor was started with Dexcom G7 native app, but that failed after a while (did not provide readings) and asked to insert a new sensor. I removed the Dexcom G7 app and installed/upgraded to Xdrip 2024.08.07 nightly hoping that would fix the data readings. Perhaps the older Xdrip and Dexcom G7 had bad interaction together. The upgrade Xdrip nightly (without Dexcom G7 installed) shows this status: I checked if I can get the battery status, and that seems to work just fine. Notice in the homescreen shows a green arrow with: "22:57 Started by transmitter" and below in the screen you see this: I think the relevant logfile is (some debug stuff redacted to xxx and changed mac-address ):
If I'm interpreting the logs write it has a problem dat with this sensor Xdrip is not able to process the backfill data. |
Beta Was this translation helpful? Give feedback.
You were using an older version of xDrip.
We have updated a lot for the sake of G7. But, we only release a stable release once every 6 months. You were using a release that did not have any of the recent updates.
You will not see that.
But, if you see a message that asks you to start, please show me and yes, ignore it.