"IOT Made Easy!" - This example demonstrates the use of the ATWINC15x0 with the WBZ451 Curiosity board to explain how to scan for an AP when running as a station
Devices: | PIC32CXBZ2 | WBZ45x |
Features: | BLE | Wi-Fi |
THE SOFTWARE ARE PROVIDED "AS IS" AND GIVE A PATH FOR SELF-SUPPORT AND SELF-MAINTENANCE. This repository contains example code intended to help accelerate client product development.
For additional Microchip repos, see: https://github.com/Microchip-MPLAB-Harmony
Checkout the Technical support portal to access our knowledge base, community forums or submit support ticket requests.
This example demonstrates the use of the ATWINC15x0 with the WBZ451 Curiosity board to explain how to scan for an AP when running as a station.
| Tools | Quantity |
|---|---|
| WBZ451 Curiosity Evaluation Kit (Rev 3) | 1 |
| WINC1500 Xplained Pro | 1 |
| XPRO-ADAPTER Click | 1 |
- Connect the WBZ451 Curiosity Evaluation Kit to the Host PC as a USB Device through a Type-A male to micro-B USB cable connected to Micro-B USB (Debug USB) port
- Connect WINC1500 Xplained Pro and WBZ451 Curiosity board as below
| WBZ451 Click connector | WBZ451 Pin name/Number | WINC1500 Xplained Pro | WINC1500 Pin Name/Number |
|---|---|---|---|
| 1 | PB1 | 10 | CHIP EN |
| 2 | PB2 | 5 | RST |
| 3 | PA9 | 15 | SPI CS |
| 4 | PA8 | 18 | SPI CLK |
| 5 | PA10 | 17 | SPI_MISO |
| 6 | PA7 | 16 | SPI_MOSI |
| 7 | Vcc | 20 | +3.3V |
| 8 | GND | 19 | GND |
| 15/16 | PA2 | 9 | IRQN (In V2 board, connect to 16) |
- WBZ451 Curiosity board can be connected to WINC1500 Xplained Pro using a XPRO-ADAPTER Click as shown below.
-
The jumper settings in XPRO-ADAPTER click board is as shown above figure. Use Jumpers and Jumper wires to connect the header as mentioned in below table.
Jumper Connections J3.1 to J4.1 J3.3 to J1.5 J3.5 to J3.6 J3.7 to J3.8 J3.9 to J3.10 J3.11 to J3.12 J4.1 to J3.1 J4.3 to J4.4 J4.6 Open J4.8 Open J4.10 Open J4.12 Open
-
This project has been verified to work with the following versions of software tools:
- MPLAB X IDE v6.00
- XC32 Compiler v4.10
- MPLAB® Code Configurator v5.1.17
- PIC32CX-BZ_DFP v1.0.107
- MCC Harmony
- csp version: v3.13.1
- core version: v3.11.1
- wireless_wifi version: v3.6.1
- dev_packs version: v3.13.1
- CMSIS-FreeRTOS version: v10.4.6
- wireless_pic32cxbz_wbz: v1.0.0
Refer Project Manifest present in harmony-manifest-success.yml under the project folder firmware\src\config\default\harmony-manifest-success.yml for more details
- Any Serial Terminal application like Tera Term terminal application.
- configure the serial settings as follows:
- Baud : 115200
- Data : 8 Bits
- Parity : None
- Stop : 1 Bit
- Flow Control : None
- configure the serial settings as follows:
Because Microchip regularly update tools, occasionally issue(s) could be discovered while using the newer versions of the tools. If the project doesn’t seem to work and version incompatibility is suspected, It is recommended to double-check and use the same versions that the project was tested with. To download original version of MPLAB Harmony v3 packages, refer to document How to Use the MPLAB Harmony v3 Project Manifest Feature
-
The "MCC - Harmony Project Graph" below depicts the harmony components utilized in this project.
-
The system configuration is depicted as follows.
-
The EIC configuration is depicted as follows.
-
The WINC configuration is depicted as follows.
-
The SPI Driver configuration is depicted as follows.
-
The SERCOM1 SPI configuration is depicted as follows.
-
The SERCOM0 UART configuration is depicted as follows.
-
The PIN configuration is depicted as follows.
- Make sure the WINC1500 firmware is v19.7.6 or higher. Please refer to the documentation in the WBZ451 serial bridge project to update the WINC1500 firmware.
- Open the Tera Term terminal application on your PC (from the Windows® Start menu by pressing the Start button)
- Choose USB Serial Com Port and Set the baud rate to 115200
- Press the switch Reset on the WBZ451 Curiosity Evaluation Kit to print the console logs.
