slzb-06p7 z2m errors on docker and odroid - plus ZHA #24118

terribleJim · 2024-09-27T07:05:51Z

terribleJim
Sep 27, 2024

I have Home Assistant (HA) running on an odroid in docker. I have portainer as well. In portainer, it shows mosquitto and zigbee2mqtt containers running. I've seen that it is possible to have ZHA (zigbee - which is on a Sonoff dongle), and zigbee2mqtt (on the slzb-06) running together with no problem. I don't know.

When trying to add an integration in HA for the slzb-06, I add the IP address of the odroid for the Host (same address as HA and Portainer), and I get a Failed to Connect error. The logs show this:

`Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-26 22:14:28] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-26 22:14:28] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-26 22:14:28] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-26 22:14:29] error:    zh:zstack:znp: Failed to determine if path is valid: 'Error: ENOENT: no such file or directory, lstat '/dev/ttyACM0''
[2024-09-26 22:14:29] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyACM0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-26 22:14:29] error:    z2m: Error while starting zigbee-herdsman
[2024-09-26 22:14:29] error:    z2m: Failed to start zigbee
[2024-09-26 22:14:29] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-26 22:14:29] error:    z2m: Exiting...
[2024-09-26 22:14:29] error:    z2m: Error: Error: No such file or directory, cannot open /dev/ttyACM0
`

My googles for this error always show somewhat different errors that I'm not sure apply here.

This is my ports:

/opt$ ls -l /dev/serial/by-id/
total 0
lrwxrwxrwx 1 root root 13 Sep 26 21:36 usb-ITEAD_SONOFF_Zigbee_3.0_USB_Dongle_Plus_V2_20240124171558-if00 -> ../../ttyACM1
lrwxrwxrwx 1 root root 13 Sep 26 21:36 usb-SMLIGHT_SMLIGHT_SLZB-06p7_d4ba796c7472ed11be711bf3fdf7b791-if00-port0 -> ../../ttyUSB0
lrwxrwxrwx 1 root root 13 Sep 26 21:36 usb-Zooz_800_Z-Wave_Stick_533D004242-if00 -> ../../ttyACM0

So I'm not sure why it is referencing ttyACM0 when it is using ttyUSB0. I've disabled zwave in docker-compose.yaml by commenting it out. I removed the zwave instance from Portainer. And I tried removing the zwave dongle from the odroid as well but then lost my ZHA automations.. it switched from ttyACM0 to ttyACM1 (or vice versa) after the reboot. So I replaced it and got ZHA working again.

I do not reference ttyACM0 in my yaml files.. that I know of anyway.

zigbee2mqtt configuration is:

# Home Assistant integration (MQTT discovery)
homeassistant: true

# allow new devices to join
permit_join: true

# MQTT settings
mqtt:
  # MQTT base topic for zigbee2mqtt MQTT messages
  base_topic: zigbee2mqtt
  # MQTT server URL
#  server: 'mqtt://192.168.60.70'
  server: 'mqtt://core-mosquitto'
  # MQTT server authentication, uncomment if required:
   user: hass
   password: itchy3

# Serial settings
serial:
  # Location of CC2531 USB sniffer
#  port: /dev/ttyUSB0
  port: /dev/serial/by-id/usb-SMLIGHT_SMLIGHT_SLZB-06p7_d4ba796c7472ed11be711bf3fdf7b791-if00-port0
  adapter: zstack

(I added the zstack adapter just to see if it helped -didn't- but got the idea from the slzb-06 setup webpage. Same errors with or without it.)

The docker-compose.yaml:

version: '3.0'

services:
  portainer:
    container_name: portainer
    image: portainer/portainer-ce
    restart: always
    ports:
      - "9000:9443/tcp"
    environment:
      - TZ=America/Anchorage
    volumes:
      - /var/run/docker.sock:/var/run/docker.sock
      - /opt/portainer:/data
  homeassistant:
    container_name: homeassistant
    image: "ghcr.io/home-assistant/home-assistant:stable"
    volumes:
      - /opt/homeassistant/config:/config
      - /etc/localtime:/etc/localtime:ro
    devices:
      # your usb device forwarding to the docker image
      - /dev/ttyUSB0:/dev/ttyUSB0
    restart: unless-stopped
    privileged: true
    network_mode: host

#  zwavejs2mqtt:
 #   container_name: zwavejs2mqtt
 #   image: zwavejs/zwavejs2mqtt:latest
 #   restart: always
 #   tty: true
 #   stop_signal: SIGINT
 #   environment:
 #     - SESSION_SECRET=1zbcxlsi5nad
 #     - ZWAVEJS_EXTERNAL_CONFIG=/usr/src/app/store/.config-db
      # Uncomment if you want log times and dates to match your timezone instead of UTC
      # Available at https://en.wikipedia.org/wiki/List_of_tz_database_time_zones
      #- TZ=America/New_York
 #   devices:
      # Do not use /dev/ttyUSBX serial devices, as those mappings can change over time.
      # Instead, use the /dev/serial/by-id/X serial device for your Z-Wave stick.
 #     - '/dev/serial/by-id/usb-Zooz_800_Z-Wave_Stick_533D004242-if00:/dev/zwave'
 #   volumes:
 #     - /opt/z-wave-js/:/usr/src/app/store
 #   ports:
 #     - "8091:8091" # port for web interface
 #     - "3000:3000" # port for Z-Wave JS websocket server
  duplicati:
    image: lscr.io/linuxserver/duplicati:latest
    container_name: duplicati
    environment:
      - PUID=1000
      - PGID=1000
      - TZ=America/Anchorage
      - CLI_ARGS= #optional
    volumes:
      - /opt/duplicati/config:/config
      - /opt:/source
    ports:
      - 8200:8200
    restart: unless-stopped
## wyoming
  whisper:
    container_name: whisper
    image: rhasspy/wyoming-whisper
    command: --model base-int8 --language fr
    volumes:
      - ./whisper-data:/data
    environment:
      - TZ=America/Anchorage
    restart: unless-stopped
    ports:
      - 10300:10300

  piper:
    container_name: piper
    image: rhasspy/wyoming-piper
    command: --voice fr-siwis-medium
    volumes:
      - ./piper-data:/data
    environment:
      - TZ=America/Anchorage
    restart: unless-stopped
    ports:
      - 10200:10200

  mosquitto:
    image: eclipse-mosquitto
    container_name: mosquitto
    volumes:
      - /opt/mosquitto:/mosquitto
      - /opt/mosquitto/data:/mosquitto/data
      - /opt/mosquitto/log:/mosquitto/log
    ports:
      - 1883:1883
      - 9001:9001

  zigbee2mqtt:
    container_name: zigbee2mqtt
    image: koenkk/zigbee2mqtt
    restart: unless-stopped
    volumes:
      - ./data:/app/data
      - /run/udev:/run/udev:ro
    ports:
        # Frontend port
     - 8080:8080
    environment:
      - TZ=America/Anchorage
    devices:
       # Make sure this matched your adapter location
    #  - /dev/ttyUSB0
      - '/dev/serial/by-id/usb-SMLIGHT_SMLIGHT_SLZB-06p7_d4ba796c7472ed11be711bf3fdf7b791-if00-port0:/dev/ttyUSB0'

Any ideas on how to fix this? Happy to provide more info if needed. /jd

[edit].. and I chowned the tty's as the odroid user to give user permissions.

chris-1243 · 2024-09-27T20:52:46Z

chris-1243
Sep 27, 2024

As you map /dev/serial/by-id/...:/dev/ttyUSB0 in your docker-compose.yaml in Z2M configuration.yaml, you should use /dev/ttyUSB0.

serial:
  port: /dev/ttyUSB0

13 replies

chris-1243 Sep 28, 2024

I just checked again your last docker-compose.yaml, configuration.yaml and log...

Could youbtry this ?

Docker file:

zigbee2mqtt:
    container_name: zigbee2mqtt
    image: koenkk/zigbee2mqtt
    restart: unless-stopped
    volumes:
      - /opt/zigbee2mqtt/data:/app/data
      - /run/udev:/run/udev:ro
    ports:
        # Frontend port
      - 8080:8080
    environment:
      - TZ=America/Anchorage
    devices:
       # Make sure this matched your adapter location
      - /dev/serial/by-id/usb-SMLIGHT_SMLIGHT_SLZB-06p7_d4ba796c7472ed11be711bf3fdf7b791-if00-port0
:/dev/ttyUSB0

where /opt/zigbee2mqtt/data points to the folder on your computer where the z2m data are stored.

Z2M configuration:

# Home Assistant integration (MQTT discovery)
homeassistant: true

# allow new devices to join
permit_join: false

# MQTT settings
mqtt:
  # MQTT base topic for zigbee2mqtt MQTT messages
  base_topic: zigbee2mqtt
  # MQTT server URL
  server: 'mqtt://192.168.60.70:1883'
  # MQTT server authentication, uncomment if required:
   user: #your mqtt user
   password: #your  mqtt password

# Serial settings
serial:
  # Location of CC2531 USB sniffer
  port: /dev/ttyUSB0
  adapter: zstack

# Will run frontend on port 8080
frontend: true

If you may provide a log after this, it would be great. All the adices given by @djurny are a good start as well😉

djurny Sep 28, 2024

By the way... are you also running a mosquitto service somewhere in your network? mosquitto is the piece of software that listens to MQTT traffic and which enables HASS to talk to zigbee2mqtt (and vice versa).
"Nothing to see here."
Groetjes,

terribleJim Sep 28, 2024
Author

Thank you Chris,

My setup has /opt/zigbee2mqtt/data as you suggested. Making those changes to the config files I get the following errors: (I had to comment out the user and password lines until I can figure out indentation on them.. kept getting errors of bad indents.)

Using '/app/data' as data directory
Starting Zigbee2MQTT [2024-09-28 15:12:42] info: [2024-09-28 15:12:42] info: [2024-09-28 15:12:42] info: [2024-09-28 15:12:43] info: [2024-09-28 15:12:43] info: [2024-09-28 15:12:44] info: [2024-09-28 15:12:45] info: [2024-09-28 15:13:03] error: [2024-09-28 15:13:03] error: [2024-09-28 15:13:03] error: [2024-09-28 15:13:03] error: [2024-09-28 15:13:04] error: at ZStackAdapter.start at Controller.start at Zigbee.start (/app/lib/z at Controller.start at start (/app/index.js:154:5)
Using '/app/data' as data directory
Starting Zigbee2MQTT [2024-09-28 15:13:13] info: [2024-09-28 15:13:13] info: [2024-09-28 15:13:13] info: [2024-09-28 15:13:14] info: [2024-09-28 15:13:14] info: [2024-09-28 15:13:14] info: [2024-09-28 15:13:16] info: without watchdog.
z2m: Logging to console, file (filename: log.log)
z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
z2m: Starting zigbee-herdsman (0.57.3)
zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
zh:zstack:znp: Serialport opened
zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
zh:zstack:znp: Skip bootloader for CC2652/CC1352
z2m: Error while starting zigbee-herdsman
z2m: Failed to start zigbee
z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
z2m: Exiting...
z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
(/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
(/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
igbee.ts:64:27)
(/app/lib/controller.ts:140:27)
without watchdog.
z2m: Logging to console, file (filename: log.log)
z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
z2m: Starting zigbee-herdsman (0.57.3)
zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
zh:zstack:znp: Serialport opened
zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
zh:zstack:znp: Skip bootloader for CC2652/CC1352

djurny Sep 29, 2024

Hi there,
Assuming you pasted the entire zigbee2mqtt log up in here, it looks like the second attempt of it starting works without any errors.
Perhaps it's a good idea to first get zigbee2mqtt up and running, before adding HASS or any HASS integration into the mix.
So...
Can you remove the homeassistant things from your Docker compose file?
After that, make sure the Docker compose file maps /app/data to the location where your configuration.yaml is located.
Then start the Docker composition.
Fire up your browser and connect to the zigbee2mqtt frontend to see if that is working or not.
Let us know what that produces.
Thanks,
Groetjes,

terribleJim Sep 29, 2024
Author

Wasn't the entire log.. seems like it is endless.. just went for a walk and when I came back.. first thing was to look at the log. It is like this:


<snip>
Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 16:35:57] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 16:35:57] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 16:35:57] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 16:35:58] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 16:35:58] info:     zh:zstack:znp: Serialport opened
[2024-09-28 16:35:58] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 16:35:59] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352
[2024-09-28 16:36:18] error:    z2m: Error while starting zigbee-herdsman
[2024-09-28 16:36:18] error:    z2m: Failed to start zigbee
[2024-09-28 16:36:18] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-28 16:36:18] error:    z2m: Exiting...
[2024-09-28 16:36:18] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
    at ZStackAdapter.start (/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
    at Controller.start (/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
    at Zigbee.start (/app/lib/zigbee.ts:64:27)
    at Controller.start (/app/lib/controller.ts:140:27)
    at start (/app/index.js:154:5)
Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 16:36:28] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 16:36:28] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 16:36:28] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 16:36:29] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 16:36:29] info:     zh:zstack:znp: Serialport opened
[2024-09-28 16:36:29] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 16:36:30] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352
[2024-09-28 16:36:49] error:    z2m: Error while starting zigbee-herdsman
[2024-09-28 16:36:49] error:    z2m: Failed to start zigbee
[2024-09-28 16:36:49] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-28 16:36:49] error:    z2m: Exiting...
[2024-09-28 16:36:49] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
    at ZStackAdapter.start (/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
    at Controller.start (/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
    at Zigbee.start (/app/lib/zigbee.ts:64:27)
    at Controller.start (/app/lib/controller.ts:140:27)
    at start (/app/index.js:154:5)
Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 16:36:59] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 16:36:59] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 16:36:59] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 16:37:00] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 16:37:00] info:     zh:zstack:znp: Serialport opened
[2024-09-28 16:37:00] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 16:37:01] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352
[2024-09-28 16:37:20] error:    z2m: Error while starting zigbee-herdsman
[2024-09-28 16:37:20] error:    z2m: Failed to start zigbee
[2024-09-28 16:37:20] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-28 16:37:20] error:    z2m: Exiting...
[2024-09-28 16:37:20] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
    at ZStackAdapter.start (/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
    at Controller.start (/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
    at Zigbee.start (/app/lib/zigbee.ts:64:27)
    at Controller.start (/app/lib/controller.ts:140:27)
    at start (/app/index.js:154:5)
Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 16:37:30] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 16:37:30] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 16:37:30] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 16:37:31] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 16:37:31] info:     zh:zstack:znp: Serialport opened
[2024-09-28 16:37:31] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 16:37:32] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352

I can give a try to what you suggest. Will let you know. (Mosquitto is running in portainer.)

terribleJim · 2024-09-29T01:07:44Z

terribleJim
Sep 29, 2024
Author

Tried it and cannot connect via http://192.168.60.70:8080, where I think it should be.

In the portainer image below, lower right hand corner for Z2M where it says 8080 - if I hover my mouse over that it says listening on 0.0.0.0:8080. That doesn't seem right. And the log for Z2M is constantly scrolling.. with errors: starting, then error starting.. Maybe something with the "adapter"? (I've restarted mosquitto as well.. didn't catch it in the print screen image..)

0 replies

djurny · 2024-09-29T05:29:02Z

djurny
Sep 29, 2024

Hi there,
Did you try to unplug the USB dongle and put it back in again? I recall I had similar error with my Sonoff Zigbee 3.0 USB dongle Pro after I upgraded firmware on it, it somehow got stuck and needed to be re-plugged to have z2m communicate with it properly.
After the dongle communication is fixed, not sure if z2m will refuse to start due to MQTT broker/server not running, but logging should be clear enough to point to the next hurdle.
Groetjes,

1 reply

djurny Sep 29, 2024

About the container, you do need to tell portainer to map port 8080 from outside to inside the container, otherwise you cannot login to the frontend. Best to use "host network" option in portainer. The 0.0.0.0 just indicates that it's listening on all interfaces known to/on/in the container, no need to worry about that. If z2m starts up fully, which might take around 30 sec - 1 minute, the frontend should be reachable.
Groetjes,

terribleJim · 2024-09-29T05:42:28Z

terribleJim
Sep 29, 2024
Author

Hello,
I was just thinking if maybe my USB extension cable wasn't good so just changed it. Of course, unplugging the dongle by doing so. It didn't seem to make a difference. Also, for the 0.0.0.0, I had read that by entering the server IP address in the environment part of portainer that it would then listen to that ip address.. I did change it then, but didn't seem to make any difference. I could change it back to 0.0.0.0 if important.

Logs very similar to before.. been tweaking on this or that, but no difference.

Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 21:39:26] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 21:39:26] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 21:39:26] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 21:39:27] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 21:39:27] info:     zh:zstack:znp: Serialport opened
[2024-09-28 21:39:27] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 21:39:28] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352
[2024-09-28 21:39:47] error:    z2m: Error while starting zigbee-herdsman
[2024-09-28 21:39:47] error:    z2m: Failed to start zigbee
[2024-09-28 21:39:47] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-28 21:39:47] error:    z2m: Exiting...
[2024-09-28 21:39:47] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
    at ZStackAdapter.start (/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
    at Controller.start (/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
    at Zigbee.start (/app/lib/zigbee.ts:64:27)
    at Controller.start (/app/lib/controller.ts:140:27)
    at start (/app/index.js:154:5)
Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 21:39:57] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 21:39:57] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 21:39:57] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 21:39:58] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 21:39:58] info:     zh:zstack:znp: Serialport opened
[2024-09-28 21:39:58] info:     zh:zstack:znp: Writing CC2530/CC2531 skip bootloader payload
[2024-09-28 21:39:59] info:     zh:zstack:znp: Skip bootloader for CC2652/CC1352
[2024-09-28 21:40:18] error:    z2m: Error while starting zigbee-herdsman
[2024-09-28 21:40:18] error:    z2m: Failed to start zigbee
[2024-09-28 21:40:18] error:    z2m: Check https://www.zigbee2mqtt.io/guide/installation/20_zigbee2mqtt-fails-to-start.html for possible solutions
[2024-09-28 21:40:18] error:    z2m: Exiting...
[2024-09-28 21:40:18] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)
    at ZStackAdapter.start (/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:123:27)
    at Controller.start (/app/node_modules/zigbee-herdsman/src/controller/controller.ts:138:29)
    at Zigbee.start (/app/lib/zigbee.ts:64:27)
    at Controller.start (/app/lib/controller.ts:140:27)
    at start (/app/index.js:154:5)

7 replies

terribleJim Sep 29, 2024
Author

Hello,
I gave a powered hub a shot and didn't make a difference. Since my odroid is headless I connected the dongle into my computer. The LEDs just showed yellow.. the blue LED came on only briefly at first then didn't come back on. So I hooked it up to the computer with an ethernet cable.. so this image shows ethernet mode now. It is the only way I seem to be able to get to the device webpage.

chris-1243 Sep 29, 2024

[2024-09-28 16:36:18] error:    z2m: Error: Failed to connect to the adapter (Error: SRSP - SYS - ping after 6000ms)

Your adapter has crashed or Z2M can not talk to it.

From your last picture, I would check if there is a setting which must be enabled in tje esp32 to have your dongle to communicate via USB. Your model is a P7 so it is based on a TI chip, zstack driver.

As @djurny suggested. Stop HA container first and try to get your Z2M working to avoid problem. In order to have it eorking properly:

MQTT must be working and configured correctly (user, password if any);
your coordinator has to be reqchable via USB or LAN.

As SLZB-06P7 is a LAN coordinator, why do not you use it through your network?

zigbee2mqtt:
    container_name: zigbee2mqtt
    image: koenkk/zigbee2mqtt
    restart: unless-stopped
    volumes:
      - /opt/zigbee2mqtt/data:/app/data
      - /run/udev:/run/udev:ro
    ports:
        # Frontend port
      - 8080:8080
    environment:
      - TZ=America/Anchorage
    devices:
       # Make sure this matched your adapter location
#      - /dev/serial/by-id/usb-SMLIGHT_SMLIGHT_SLZB-06p7_d4ba796c7472ed11be711bf3fdf7b791-if00-port0
:/dev/ttyUSB0

# Home Assistant integration (MQTT discovery)
homeassistant: true

# allow new devices to join
permit_join: false

# MQTT settings
mqtt:
  # MQTT base topic for zigbee2mqtt MQTT messages
  base_topic: zigbee2mqtt
  # MQTT server URL
  server: 'mqtt://192.168.60.70:1883'
  # MQTT server authentication, uncomment if required:
   user: #your mqtt user
   password: #your  mqtt password

# Serial settings
serial:
  # Location of CC2531 USB sniffer
  port: tcp://ipaddress:6638
  adapter: zstack

# Will run frontend on port 8080
frontend: true

Change ipaddress by the one on your coordinator😉

https://smlight.tech/manual/slzb-06/guide/installation/

terribleJim Sep 29, 2024
Author

Something happened.. with the blue LED coming on I thought it showed it was in USB mode.. But in that webinterface I found another setting that I enabled for USB. I plugged it back into the odroid and here's the log... looks like something happened that may be good.
As far as not using it on my lan, I don't have a POE switch yet. Will order one, but will take a few weeks to get to me (I'm off the road system in NW Alaska). It is bedtime so don't have time to see what might be working or not now.. will look again in the morning.

Using '/app/data' as data directory
Starting Zigbee2MQTT without watchdog.
[2024-09-28 23:47:12] info:     z2m: Logging to console, file (filename: log.log)
[2024-09-28 23:47:12] info:     z2m: Starting Zigbee2MQTT version 1.40.1 (commit #403d3c0)
[2024-09-28 23:47:12] info:     z2m: Starting zigbee-herdsman (0.57.3)
[2024-09-28 23:47:13] info:     zh:zstack:znp: Opening SerialPort with {"path":"/dev/ttyUSB0","baudRate":115200,"rtscts":false,"autoOpen":false}
[2024-09-28 23:47:13] info:     zh:zstack:znp: Serialport opened
[2024-09-28 23:47:14] info:     z2m: zigbee-herdsman started (resumed)
[2024-09-28 23:47:14] info:     z2m: Coordinator firmware version: '{"meta":{"maintrel":1,"majorrel":2,"minorrel":7,"product":1,"revision":20240716,"transportrev":2},"type":"zStack3x0"}'
[2024-09-28 23:47:14] info:     z2m: Currently 0 devices are joined.
[2024-09-28 23:47:14] info:     z2m: Zigbee: disabling joining new devices.
[2024-09-28 23:47:14] info:     z2m: Connecting to MQTT server at mqtt://192.168.60.70:1883
[2024-09-28 23:47:14] info:     z2m: Connected to MQTT server
[2024-09-28 23:47:14] info:     z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/bridge/state', payload '{"state":"online"}'
[2024-09-28 23:47:14] info:     z2m: Started frontend on port 8080
[2024-09-28 23:47:14] info:     z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/bridge/state', payload '{"state":"online"}'
[2024-09-28 23:47:14] info:     z2m: Zigbee2MQTT started!
[2024-09-28 23:47:19] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/binary_sensor/1221051039810110150109113116116_0x00124b002a7616f7/connection_state/config', payload '{"device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"device_class":"connectivity","entity_category":"diagnostic","name":"Connection state","object_id":"zigbee2mqtt_bridge_connection_state","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"payload_off":"offline","payload_on":"online","state_topic":"zigbee2mqtt/bridge/state","unique_id":"bridge_0x00124b002a7616f7_connection_state_zigbee2mqtt","value_template":"{{ value_json.state }}"}'
[2024-09-28 23:47:19] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/binary_sensor/1221051039810110150109113116116_0x00124b002a7616f7/restart_required/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"device_class":"problem","enabled_by_default":false,"entity_category":"diagnostic","name":"Restart required","object_id":"zigbee2mqtt_bridge_restart_required","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"payload_off":false,"payload_on":true,"state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_restart_required_zigbee2mqtt","value_template":"{{ value_json.restart_required }}"}'
[2024-09-28 23:47:19] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/button/1221051039810110150109113116116_0x00124b002a7616f7/restart/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","command_topic":"zigbee2mqtt/bridge/request/restart","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"device_class":"restart","name":"Restart","object_id":"zigbee2mqtt_bridge_restart","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"payload_press":"","unique_id":"bridge_0x00124b002a7616f7_restart_zigbee2mqtt"}'
[2024-09-28 23:47:19] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/select/1221051039810110150109113116116_0x00124b002a7616f7/log_level/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","command_template":"{\"options\": {\"advanced\": {\"log_level\": \"{{ value }}\" } } }","command_topic":"zigbee2mqtt/bridge/request/options","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"entity_category":"config","name":"Log level","object_id":"zigbee2mqtt_bridge_log_level","options":["error","warning","info","debug"],"origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_log_level_zigbee2mqtt","value_template":"{{ value_json.log_level | lower }}"}'
[2024-09-28 23:47:19] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/sensor/1221051039810110150109113116116_0x00124b002a7616f7/version/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"entity_category":"diagnostic","icon":"mdi:zigbee","name":"Version","object_id":"zigbee2mqtt_bridge_version","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_version_zigbee2mqtt","value_template":"{{ value_json.version }}"}'
[2024-09-28 23:47:20] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/sensor/1221051039810110150109113116116_0x00124b002a7616f7/coordinator_version/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"enabled_by_default":false,"entity_category":"diagnostic","icon":"mdi:chip","name":"Coordinator version","object_id":"zigbee2mqtt_bridge_coordinator_version","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_coordinator_version_zigbee2mqtt","value_template":"{{ value_json.coordinator.meta.revision }}"}'
[2024-09-28 23:47:20] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/sensor/1221051039810110150109113116116_0x00124b002a7616f7/network_map/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"enabled_by_default":false,"entity_category":"diagnostic","json_attributes_template":"{{ value_json.data.value | tojson }}","json_attributes_topic":"zigbee2mqtt/bridge/response/networkmap","name":"Network map","object_id":"zigbee2mqtt_bridge_network_map","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"state_topic":"zigbee2mqtt/bridge/response/networkmap","unique_id":"bridge_0x00124b002a7616f7_network_map_zigbee2mqtt","value_template":"{{ now().strftime('%Y-%m-%d %H:%M:%S') }}"}'
[2024-09-28 23:47:20] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/sensor/1221051039810110150109113116116_0x00124b002a7616f7/permit_join_timeout/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"device_class":"duration","entity_category":"diagnostic","name":"Permit join timeout","object_id":"zigbee2mqtt_bridge_permit_join_timeout","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_permit_join_timeout_zigbee2mqtt","unit_of_measurement":"s","value_template":"{{ iif(value_json.permit_join_timeout is defined, value_json.permit_join_timeout, None) }}"}'
[2024-09-28 23:47:20] info:     z2m:mqtt: MQTT publish: topic 'homeassistant/switch/1221051039810110150109113116116_0x00124b002a7616f7/permit_join/config', payload '{"availability":[{"topic":"zigbee2mqtt/bridge/state","value_template":"{{ value_json.state }}"}],"availability_mode":"all","command_topic":"zigbee2mqtt/bridge/request/permit_join","device":{"hw_version":"zStack3x0 20240716","identifiers":["zigbee2mqtt_bridge_0x00124b002a7616f7"],"manufacturer":"Zigbee2MQTT","model":"Bridge","name":"Zigbee2MQTT Bridge","sw_version":"1.40.1"},"icon":"mdi:human-greeting-proximity","name":"Permit join","object_id":"zigbee2mqtt_bridge_permit_join","origin":{"name":"Zigbee2MQTT","sw":"1.40.1","url":"https://www.zigbee2mqtt.io"},"payload_off":"false","payload_on":"true","state_topic":"zigbee2mqtt/bridge/info","unique_id":"bridge_0x00124b002a7616f7_permit_join_zigbee2mqtt","value_template":"{{ value_json.permit_join | lower }}"}'
odroid@server:/opt$

chris-1243 Sep 29, 2024

[2024-09-28 23:47:14] info: z2m: Zigbee2MQTT started!

You are good!!!

Go to ipaddress:8080 and you should have access to your frontend

terribleJim Sep 29, 2024
Author

I just want to say a very heart felt thank you to you folks for helping out. I feel I may have wasted your time - should have explored that interface a bit more first.. but again, I sure appreciate your time! I did learn some stuff from this so there's that!

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

slzb-06p7 z2m errors on docker and odroid - plus ZHA #24118

{{title}}

{{editor}}'s edit

{{editor}}'s edit

Replies: 4 comments 21 replies

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

Select a reply

slzb-06p7 z2m errors on docker and odroid - plus ZHA #24118

Replies: 4 comments · 21 replies

terribleJim Sep 28, 2024 Author

terribleJim Sep 29, 2024 Author

terribleJim Sep 29, 2024 Author

terribleJim Sep 29, 2024 Author

terribleJim Sep 29, 2024 Author

terribleJim Sep 29, 2024 Author

terribleJim Sep 29, 2024 Author

Replies: 4 comments 21 replies

terribleJim Sep 28, 2024
Author

terribleJim Sep 29, 2024
Author

terribleJim
Sep 29, 2024
Author

terribleJim
Sep 29, 2024
Author

terribleJim Sep 29, 2024
Author

terribleJim Sep 29, 2024
Author

terribleJim Sep 29, 2024
Author