Replies: 100 comments 200 replies
-
I tried flashing SLZB-06P7 on CC1352P2_CC2652P_other_coordinator_20240710.hex but that didn't seem to work, granted It was my first time trying to flash via USB. It just wouldn't verify for me. And the adapter wouldn't start afterwords. I did managed to flash 20240316 over USB again and it works again. I'm not sure I did something wrong or not, as using a different fw image seemed to work fine. |
Beta Was this translation helpful? Give feedback.
-
deleted since I don't think it's a firmware issue |
Beta Was this translation helpful? Give feedback.
-
Thanks @Koenkk, what are the improvements for ZigBee on SDK 7.41? |
Beta Was this translation helpful? Give feedback.
-
Coordinator Device: SONOFF Zigbee 3.0 USB Dongle Plus (CC2652P)
After upgrading to version 20240710, two devices showed an error and had to be again paired. Now the device seems to be stabilized. |
Beta Was this translation helpful? Give feedback.
-
Flashed it successfully, will post a reply to my own thread for any issues, but didn't see any devices (that I've noticed) not pair correctly after a flash. So will wait and see, so far all looking good. |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 141 all devices work stably |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 132 [End devices: 90 - Router: 42] |
Beta Was this translation helpful? Give feedback.
-
Can I use the baud rate 460800 on this firmware? |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 23 |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 79 (End devices: 51 Router: 28) |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 85 (End devices: 45, Router: 40) |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 45 (End devices: 26, Router: 19) |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 89 (End devices: 61 Router: 28) Update: I've tried 20240710 one more time, it worked ok for two days, but on third Buffer full error, restarting RPi4 host repairs the issue, but it works for few minutes and again Buffer full error and nothing is working anymore. Additionally I'm having random network slowdowns with error Read response to (address of the device) failed. |
Beta Was this translation helpful? Give feedback.
-
Coordinator Device: SONOFF Zigbee 3.0 USB Dongle Plus (CC2652P) Amount of devices in network: 61 (Routers: 31, End devices: 30)
|
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 43 (End devices: 36 Routers: 7) Updated and rebooted the device, and that went well. 2 hours in, and I noticed all 4 of my Ikea Tradfri outlets devices were not responding, so I just unplugged them and plugged them back in, and they came back. Perhaps if I left them, they would have come back by themselves, but considering they are critical to my network, I wanted to make sure they were working first |
Beta Was this translation helpful? Give feedback.
-
Z-Stack 20221226 has been working flawlessly. After seeing the mixed comments here, not keen to update. As always with updates, if the older version is working and the new release does not bring anything new, no point in updating. |
Beta Was this translation helpful? Give feedback.
-
Zigbee2MQTT version
|
Beta Was this translation helpful? Give feedback.
-
Flashed SLZB-06P7 with 20240710 FW a couple of weeks ago. Since the new FW was applied, the device randomly stops receiving updates from devices, while Zigbee2MQTT reports no issues except communication errors. Restarting ESP32 or Zigbee (the last time I restarted Zigbee, was not enough, I had to restart ESP32 for the device to start responding; it could have been I did not give enough time for the devices to start reporting - gave it a couple of minutes which was my prior experience with the failure) the SLZB-06P7 starts processing packets again. Time between failures, one took 2 days, the other 6 days. The last 2 weeks the device failed with the same issue 3 times. Initially I thought it was an isolated incident, but now I am more confident is a FW issue. Are these type of issues related to TI chipsets only? |
Beta Was this translation helpful? Give feedback.
-
Just upgraded (53 devices, SonOff ZBdongle-P), and it does appear more stable (especially during the OTA updates). Nice, thank you so much! |
Beta Was this translation helpful? Give feedback.
-
You can interchange SLZB-06P7 with UZG-01 without changing anything. Just shut down Z2M replace the coordinator and fire up Z2M. The same applies to any FW upgrade/downgrade. There is no need to re-pair anything. You need to be patient as it takes a couple of hours for the network to stabilise and at least a day for everything to be fully connected. If using 20240710 with 1.40.0 I have noticed when something goes offline, just try to re-interview. It has worked for me in one instance, but took almost a day. I have tried on a second device and waiting to see if it has worked. |
Beta Was this translation helpful? Give feedback.
-
zigbee2mqtt addod at Home assistance doesn't work. |
Beta Was this translation helpful? Give feedback.
-
Another complete crash for me. here. Worst version to date unfortunately |
Beta Was this translation helpful? Give feedback.
-
Zigbee2mqtt has the latest update: 1.40.1-1 Again last night total adapter crash... (Web gui still works, and zigbee reset on UZG does not help). After PoE reset, and I let it for 1 hour to stabilize, network was a mess.. Ikea bulbs were reporting no network route. had to reset all router devices with appartment elec. braker. Yesterday befor the crash I noticed that everything is very laggy. And it is like this every 1-2 weeks from the day this firmvare version is released. Already rejoined all devices. We can not say it works but sometimes devices disconect. That is not Producton ready then. My wife will kill me soon :) |
Beta Was this translation helpful? Give feedback.
-
We all need to assist Koenkk get to the bottom of the issues. Each with their positive contribution. The process is frustrating and long but we need to get things resolved one way or another. Let's all embrace a positive attitude and assist in getting a working solution acceptable to everyone/most. Please assist any way you can. Reverting to older FW does not speed up the process of getting a handle of what the issues are. IMHO 20240710 is reliable enough for production use, although not the most desirable solution. I believe at this point nobody has a clear understanding of the full extent of the issues and therefore cannot attempt to provide a final solution. To me it seems a trial and error process until we fully understand the underlying issues. |
Beta Was this translation helpful? Give feedback.
-
If my observations are correct the fact that a device goes offline does not mean it is not operational or not communicating. Devices can show offline, yet their last seen can always show a value of a few minutes (not hours of days). So when you see a device showing offline check the last seen value as well. Until someone can articulate the availability algorithm we will not be able to contribute in a meaningful way. For my understanding, the issue is what availability is checking and how (someone posting the code snippet is fine as well). Why using 20240315 router FW shows the router always online, while using 20240716 router FW alternates between online/offline. What has changed between the two FW releases which makes availability behave in a different way. |
Beta Was this translation helpful? Give feedback.
-
This is new.... Permit join just disables after fiew seconds.... [2024-09-09 12:04:42] error: zh:controller: Failed to keep permit join alive: Error: SRSP - ZDO - mgmtPermitJoinReq after 6000ms |
Beta Was this translation helpful? Give feedback.
-
This was common for me over that last week.
Reflash the firmware to that coordinator
…On Mon, 9 Sept 2024, 8:13 pm dankocrnkovic, ***@***.***> wrote:
This is new....
Permit join just disables after fiew seconds....
[2024-09-09 12:04:42] error: zh:controller: Failed to keep permit join
alive: Error: SRSP - ZDO - mgmtPermitJoinReq after 6000ms
Error: SRSP - AF - dataRequestExt after 6000ms
at Object.start
(/app/node_modules/zigbee-herdsman/src/utils/waitress.ts:59:23)
at /app/node_modules/zigbee-herdsman/src/adapter/z-stack/znp/znp.ts:300:45
at Queue.execute
(/app/node_modules/zigbee-herdsman/src/utils/queue.ts:36:26)
at ZStackAdapter.dataRequestExtended
(/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:1245:9)
at
/app/node_modules/zigbee-herdsman/src/adapter/z-stack/adapter/zStackAdapter.ts:681:13
at Queue.execute
(/app/node_modules/zigbee-herdsman/src/utils/queue.ts:36:20)
at GreenPower.permitJoin
(/app/node_modules/zigbee-herdsman/src/controller/greenPower.ts:261:13)
at Controller.permitJoinInternal
(/app/node_modules/zigbee-herdsman/src/controller/controller.ts:311:13)
at Timeout._onTimeout
(/app/node_modules/zigbee-herdsman/src/controller/controller.ts:301:25)
—
Reply to this email directly, view it on GitHub
<#505 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AOB2WBF5TMXW43EJ56KO2C3ZVVYGHAVCNFSM6AAAAABK2RNKGCVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTANJYHEZDMMQ>
.
You are receiving this because you were mentioned.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
Normally i would do a git bisect action to find the culprit commit for weird and unknown issues with a software package. For the record i got mentioned issues with zigstar UZG-01 bridge. I tried to update 2 times to 20240710 firmware but everytime i run in weird connection issues. I will roll back to stable 20240316 for the moment |
Beta Was this translation helpful? Give feedback.
-
Amount of devices in network: 26 (End devices: 22 Routers: 4) Sonoff ZBMini worked fine: yes |
Beta Was this translation helpful? Give feedback.
-
On 4 occasions I have attempted to access the webUI of UZG-01 the coordinator rebooted - lost and re-established connection within a few seconds. The last time it happened UZG-01 was on 23 hrs uptime. I suggest you take a look at possible issues when coordinator busy a connection over the network for management could cause the connection to reset? I have not tried to setup a continuous ping to test what happens when I try to access the webUI, but this is something I intent doing and will provide feedback. |
Beta Was this translation helpful? Give feedback.
-
Update 2024-08-24:
The
20240710
firmware has been officially released. Feel free to continue discussing the firmware in this thread. Note that I will not actively monitor this discussion anymore. In case of issues with the firmware, report a new issue here. Make sure to include:Welcome to another firmware testing thread!
After testing a countless amount of different firmwares (many thanks to @nick4275 for all the testing!), we (very likely 🤞) found the root cause of the issues causing the
20230507
firmware to crash and managed to fix these (together with help from Texas Instruments).Even more excitingly, this firmware is built on the latest TI SDK (7.41).
This is a continuation of #474, #478, #483 and #496.
Download: 20240710.zip
When providing feedback copy and comment the template below:
If no breaking issues are found, this firmware will be officially released on 24 August.
Beta Was this translation helpful? Give feedback.
All reactions